树莓派的几种板载声卡的引脚定义
2018-03-13 20:55
316 查看
1、
2、
3、
图一、二采用WM8731,最后这张采用PCM5122。
树莓派3B上引脚均相同,如下:
默认系统配置:/boot/config# For more options and information see
# http://rpf.io/configtxt # Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=800
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=1
hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
如果是WM8731解码则在最后一行添加dtoverlay=audioinjector-wm8731-audio如果是PCM5122则在最后一行添加dtoverlay=hifiberry-dacplus
2、
3、
图一、二采用WM8731,最后这张采用PCM5122。
树莓派3B上引脚均相同,如下:
默认系统配置:/boot/config# For more options and information see
# http://rpf.io/configtxt # Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=800
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=1
hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
如果是WM8731解码则在最后一行添加dtoverlay=audioinjector-wm8731-audio如果是PCM5122则在最后一行添加dtoverlay=hifiberry-dacplus
相关文章推荐
- 香蕉派和树莓派的不同点及GPIO引脚定义
- USB TYPE A B C 引脚定义
- 定义结构体变量的几种方式
- C/C++定义全局变量/常量几种方法的区别
- javascript定义函数的几种方式
- TC35i的TxD和RxD引脚定义
- DB9 公头母头引脚定义及连接
- java定义二维数组的几种写法(转)
- 浅谈几种常用的JS类定义方法
- MINI PCI-E 引脚定义
- XML文档定义有几种方式?它们之间有何本质区别?解析XML文档有哪几种方式?
- C语言结构体定义的几种方法
- PCIe 接口 引脚定义 一览表
- 定义C/C++全局变量/常量几种方法的区别
- C/C++定义全局变量/常量几种方法的区别
- 备份环境的部署及实施续——第三部分 Symantec中几种备份方式的定义
- UML中几种类图的定义和表示
- c# 一维数组和二维数组的定义几种方式
- Flask中定义模型类的几种情况
- C/C++定义全局变量/常量几种方法的区别