计网-路由器配置命令
2018-02-13 13:10
351 查看
路由器配置
(一)路由器的基本配置和命令
注意:进入命令与提示符1. 用户模式
只读Router> ping/telnet/show version
2. 特权模式
用户模式下,输入enable与超级用户密码,进入特权模式
Router > enable password: Router #
特权模式可以进入全局配置模式,以便对其进行配置。
3. 设置模式
通过Console端口进入刚出厂的无配置路由器,所进入的模式。4. 全局配置模式(Global Configuration)
Router # configure terminal Router (config) # ...
5. 其他
在全局模式下进入接口配置模式Router (config) # int f0 /12
Router (config-if) #
在全局配置模式下进入虚拟终端配置模式:
Router (config) # line vty 0 15
Router (config-line) #
在全局配置模式下,进入RIP路由协议模式:
Router (config) # router rip
Router (config-router) #
6. 配置主机名
Router (config) # hostname Router-phyRouter-phy (config) #
7. 配置超级用户口令
Router (config) # enable secret phy123Router (config) # enable password 7 phy123
Router (config) #
(二) 路由器接口配置
description 描述信息Router (config) # int g6/0
Router (config-if) # description To-Blabla
bandwidth 设置带宽 单位是kbps
Router (config) # interface POS3/0
Router (config-if) # bandwidth 25000000
配置接口的IP地址
命令格式: ip address \\
Router (config) # interface f2/3
Router (config-if) # ip address 0.0.0.0 255.255.255.252
开启与关闭
Router (config) # interface f2/3
Router (config-if) # shutdown
Router (config-if) # no shutdown
(三)局域网接口配置
1. 配置标准以太网接口
interface Ethernet0 # 进入config-if description To blabla ip address 202.112.7.4 255.255.255.0 bandwidth 10000 no shutdown exit # 退到config exit # 退到Router #
2. 配置快速以太网接口
FastEthernet, f for shortinterface f2/1 ... duplex full no ip directer-broadcast no ip proxy-arp no shutdown exit exit
3. 配置千兆以太网
GigabitEthernet, g for shortinterface g0/1 ...
(四) 广域网接口配置
1. 配置异步串行口
先配置异步串行接口Async, a for short.interface a1 ip unnumbered ethernet0 encapsulation ppp async default ip address 202.112.7.129 async dynamic routing async mode interactive no shutdown exit exit
2. 配置高速同步串行接口
Serial, s for short.需要配置的参数:接口带宽,接口协议,接口IP地址。interface s1/1 description bandwidth 2048 # 2M ip address encapsulation hdlc no ip directed-broadcast no shutdown
3. 配置POS接口
POS使用的链路层协议主要有PPP和HDLCinterface POS3/0 description To blabla bandwidth 2500000 ip address 212.12.0... crc 32 #crc校验位为16和32 pos framing sdh # no ip directed-broadcast pos flag s1 s0 2 no shutdown
(五)Loopback接口配置
是一种应用广泛的虚接口。为方便管理,在每台路由器上设置环回接口,接口不受网络故障的影响。网络管理员为loopback分配一个IP地址作为管理地址,掩码255.255.255.255。
可以使用这个地址远程登陆到路由器上,进行管理配置。
int loopback 0 ip address IP 255.255.255.255 no ip route-cache no ip mroute-cache exit exit
(六)静态路由配置
已知路由表的情况下:# 全局配置模式下(config) ip route <目的网络地址><子网掩码><下一跳路由器的IP地址>
# 设置默认路由器 ip route 0.0.0.0 0.0.0.0 <下一跳>
(七)动态路由协议的配置
1. RIP
RIP只依据路由器跳数(hop)决定最佳路径,不管带宽、延时等。最大hop==15。不能携带子网掩码信息,不支持可变长掩码VLSM。自动根据ip的网络号确定掩码。
每30s更新一次路由,一般用于小型局域网。
基本配置:启动,定义参与RIP路由的网络地址。
# 在全局config模式下 router rip network 159.105.0.0 # 进入config-router network 212.112.7.0 exit exit
高级配置
# 配置被动接口 router rip passive-interface ethernet 0 # 配置路由过滤 access-list 12 deny any router rip distribute-list 12 in ethernet0 end # 配置管理距离AD # AD缺省120,AD越小路由可信度越高 router rip distance 50 # 定义邻居路由,单播发送 router rip neighbor ip
2. OSPF
OSPF可以区域划分,路由更新信息只在本区域内传播,不同区域不交换路由信息。支持大型互联网的路由选择
区域用数字表示,区域ID,32位unsigned。区域ID为0表示主干区域。
基本配置
子网配置
# 定义参与OSPF的单个IP地址 # network ip <子网> <wildcard-mask> area <区域号> # wildcard-mask子网掩码的反码 router ospf 63 network 131.107.25.1 0.0.0.0 area 0 # 网络地址 network 133.181.0.0 0.0.255.255 area 0 # area range 定义一定范围子网的聚合 area 0 range 212.37.123.0 255.255.255.0
其他的如passive-interface/distribute-list/distance/redistribute
三层交换机的配置 暂略
相关文章推荐
- Cisco路由器配置命令
- 某金融单位迈普主备用路由器完整配置命令
- 路由器基本配置命令
- Cisco路由器安全配置必用10条命令
- 思科交换机 路由器配置命令大全
- Cisco路由器配置必用10条命令
- 思科路由器常用配置命令大全
- CISCO路由器配置命令大全
- 路由器的基本配置命令
- 思科路由器常用配置命令大全
- cisco路由器配置命令大全
- 思科路由器常用配置命令大全(A-X)
- H3C的路由器配置命令一部分
- 路由器OSPF协议配置命令<一>
- 最详细的CISCO路由器配置命令及方法
- Cisco路由器安全配置必用10条命令
- 思科路由器配置命令详解及实例
- 思科路由器常用配置命令大全
- CISICO 路由器和交换机的基本配置命令
- 路由器RIP协议配置命令大全