树莓派3 配置文件conf 高分辨率 串口引脚重映射
2017-11-05 09:17
316 查看
# For more options and information see
# http://rpf.io/configtxtreadme
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=2
hdmi_mode=23
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
start_x=1
gpu_mem=128
#enable_uart=0
dtoverlay=pi3-miniuart-bt
force_turbo=1
# http://rpf.io/configtxtreadme
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=2
hdmi_mode=23
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
start_x=1
gpu_mem=128
#enable_uart=0
dtoverlay=pi3-miniuart-bt
force_turbo=1
相关文章推荐
- docker映射window本地文件夹的nginx的虚拟主机配置文件vhost.nginx.conf
- mappingResources、mappingLocations、mappingDirectoryLocations、mappingJarLocations配置映射文件时的区别
- Linux配置静态ip及resolve.conf文件内容被清除问题
- 2.2Bind建立配置文件和实体的映射「深入浅出ASP.NET Core系列」
- redis的主从配置和conf文件说明
- MyEclipse Hibernate 映射表配置文件详解
- Nginx配置文件nginx.conf中文详解(转载)
- MyBatis学习(二)-XML映射配置文件mybatis-config.xml
- keepalived.conf 默认配置文件/etc/keepalived/keepalived.conf
- Hibernate --- xxx.hbm.xml映射配置文件详解
- ant 生产hibernater配置文件跟映射文件 mysql为例
- mongodb.conf配置文件详解
- 添加JBoss插件中的hibernate tools后怎么创建hibernate配置文件和对数据库的表进行反转映射
- Nginx nginx.conf配置文件详解
- (总结)Nginx配置文件nginx.conf中文详解
- resolv.conf文件配置相关的案例
- Nginx配置文件nginx.conf详解
- (总结)Nginx配置文件nginx.conf中文详解
- python操作conf配置文件
- NHibernate之映射文件配置说明