Linux-4.9.2内核在mini2440上的移植(六)——修改MD9000驱动

本篇目标：修改DM9000驱动，使内核支持网络。

6.1 移植DM9000 网卡驱动

（1）在linux-4.9.2文件夹，输入

root@ubuntu:~/linux-4.9.2#vim arch/arm/mach-s3c24xx/mach-mini2440.c

定位到53行，添加

#include<linux/platform_data/mtd-nand-s3c2410.h>

#include <linux/dm9000.h>

 

（2）填充该平台设备的资源设置

定位到206行附近，如入下面代码：

tatic struct s3c2410_platform_nand mini2440_nand_info = {

 .tacls  = 20,

 .twrph0  = 60,

 .twrph1  = 20,

 .nr_sets = ARRAY_SIZE(mini2440_nand_sets),

 .sets  = mini2440_nand_sets,

 .ignore_unset_ecc = 1,

};
/* DM9000AEP 10/100 ethernet controller */

#define MACH_MINI2440_DM9K_BASE (S3C2410_CS4 + 0x300)
static struct resource mini2440_dm9k_resource[] = {
        [0] = {
               .start = MACH_MINI2440_DM9K_BASE,
               .end   = MACH_MINI2440_DM9K_BASE +3,
               .flags = IORESOURCE_MEM
        },
        [1] = {
               .start = MACH_MINI2440_DM9K_BASE + 4,
               .end   = MACH_MINI2440_DM9K_BASE +7,
               .flags = IORESOURCE_MEM
        },
        [2] = {
               .start = IRQ_EINT7,
               .end   = IRQ_EINT7,
               .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
        }
};
/*
 *  *  *The DM9000 has no eeprom, and it's MAC address is set by
 *   *   *the bootloader before starting the kernel.
 *    *   */
static struct dm9000_plat_data mini2440_dm9k_pdata = {
        .flags          = (DM9000_PLATF_16BITONLY |DM9000_PLATF_NO_EEPROM),
};
static struct platform_device mini2440_device_eth = {
        .name           = "dm9000",
        .id             = -1,
       .num_resources  = ARRAY_SIZE(mini2440_dm9k_resource),
       .resource       =mini2440_dm9k_resource,
        .dev            = {
               .platform_data  =&mini2440_dm9k_pdata,
        },
};
 
static struct platform_device *mini2440_devices[]__initdata = {
       &s3c_device_ohci,
       &s3c_device_lcd,
       &s3c_device_wdt,
       &s3c_device_i2c0,
       &s3c_device_iis,
       &s3c_device_nand,
        &mini2440_device_eth,
};
保存退出。

6.2 调整DM9000 所用的位宽寄存器

DM9000的驱动是有问题的，不能直接使用，需要修改

root@ubuntu:~/linux-4.9.2#vim drivers/net/ethernet/davicom/dm9000.c

 

(1)打开linux-4.9.2/drivers/net/ethernet/davicom/dm9000.c，定位到49行附近，添加2410 相关的配置定义，如下红色部分：

#include <asm/delay.h>

#include <asm/irq.h>

#include <asm/io.h>

#include "dm9000.h"
#define CONFIG_ARCH_S3C2410

#if defined(CONFIG_ARCH_S3C2410)

#include<../../../../arch/arm/mach-s3c24xx/regs-mem.h>

#endif

(2) 在dm9000 设备的初始化函数中添加如下红色部分，这里是配置DM9000 所用片选总线的时序，因为mini2440 目前只有一个通过总线外扩的设备，在此设备驱动中直接修改相关的寄存器配置会更加容易理解一些，当然这部分也可以放到mach-mini2440.c 中。

打开linux-4.9.2/drivers/net/ethernet/davicom/dm9000.c，定位到914行附近，加入下面代码：

/*

 * Initialize dm9000 board

 */

static void

dm9000_init_dm9000(struct net_device *dev)

{

#ifdefined(CONFIG_ARCH_S3C2410)

       unsigned int oldval_bwscon = *(volatile unsigned int*)S3C2410_BWSCON;                unsignedint oldval_bankcon4 = *(volatile unsigned int *)S3C2410_BANKCON4;            *((volatile unsigned int*)S3C2410_BWSCON) =                               
                  (oldval_bwscon &~(3<<16)) | (1<<16) | (1<<18) | (1<<19);                     *((volatile unsigned int*)S3C2410_BANKCON4) = 0x1f7c;

#endif

 

        struct board_info *db= netdev_priv(dev);

        unsigned int imr;

        unsigned int ncr;

到此为止 DM9000 就已经移植结束了。

 

6.3编译测试

root@ubuntu:~/linux-4.9.2# make -j8

root@ubuntu:~/linux-4.9.2#./mkuImage.sh