Marvell 98DX3236系列交换机Uboot及内核文件烧写
2017-09-01 17:59
1291 查看
1. 开发环境
开发板硬件相关
(1)交换机开发板型号:RD-XC3-24G4XG-B
(2)交换机CPU型号:98DX3236
(3)交换机PHY芯片型号:88E1680
开发板软件相关
(1)CPLD(LC4032V)程序:ac3_24p.jed
(2)I2C存储芯片(AT24C128B)程序:EEPROM-Demo.bin
(3)SPIflash芯片(MX25L25735EMI-12G)Uboot文件:SPI-DEMO.bin
(4)内核文件:ubifs_arm10.image
烧录工具及软件
(1)周立功烧录器SmartPRO T9000,配套软件SmartPRO 2008(用于向MX25L25735烧写Uboot文件);
(2)烧录器superpro-SP580U,配套软件SUPERPRO USB series(用于向AT24C128B烧写I2C存储芯片程序);
(3)LatticeUSB下载线,配套软件ispVM System(用于向LC4032V烧写CPLD程序)。
2. Uboot烧写
Uboot的烧写比较简单,采用烧录器将Uboot程序下载到SPIflash中即可。
在烧写时请注意以下几点:
(1)要确保烧录器选择的芯片型号与实际被烧写的芯片型号保持一致;
(2)已焊接过的SPIflash芯片需要使用洗板水清晰管脚上的松香,防止管脚与芯片座接触不良;
(3)为了确保二进制程序正确烧入芯片内,可以使用烧程软件读出被烧写的程序并与原始程序对比,如果内容一致则烧录成功;
在交换机使用Uboot进行硬件资源引导时,必须先确保I2C和CPLD已烧写正确程序,否则CPU无法正常工作,串口无如何信息输出。
3. 内核烧写
(1)将“ubifs_arm10.image”文件复制到FAT或FAT32格式的U盘,把该U盘插入板上的USB接口。
给开发板上电,当出现“Hit any key to stop autoboot”提示时,敲击键盘任意键并出现“Marvell>> ”,串口显示如下:
(2)在串口中输入“nand erase.chip”,对NANDflash进行擦除操作!
Marvell>> nand erase.chip
Marvell>> usb start
Marvell>> mtdburn usb 0 FAT ubifs_arm10.image NAND
Do you want to continue ? [Y/n] y
Do you want to continue ? [Y/n] y
Marvell>> boot
(6)交换机系统测试
通过向串口写入命令“cpssInitSystem 19,2,0”配置交换机进行端口功能测试,如果测试结束后串口输出“Init system returned:0”,说明系统已被正确的初始化!
Console# cpssInitSystem 19,2,0
4.内核烧写VB脚本程序
说明:
(1)程序类型:Visual Basic脚本语言
(2)配套软件:SecureCRT 5.2.2
(3)交换机CPU型号:98DX3236
开发板硬件相关
(1)交换机开发板型号:RD-XC3-24G4XG-B
(2)交换机CPU型号:98DX3236
(3)交换机PHY芯片型号:88E1680
开发板软件相关
(1)CPLD(LC4032V)程序:ac3_24p.jed
(2)I2C存储芯片(AT24C128B)程序:EEPROM-Demo.bin
(3)SPIflash芯片(MX25L25735EMI-12G)Uboot文件:SPI-DEMO.bin
(4)内核文件:ubifs_arm10.image
烧录工具及软件
(1)周立功烧录器SmartPRO T9000,配套软件SmartPRO 2008(用于向MX25L25735烧写Uboot文件);
(2)烧录器superpro-SP580U,配套软件SUPERPRO USB series(用于向AT24C128B烧写I2C存储芯片程序);
(3)LatticeUSB下载线,配套软件ispVM System(用于向LC4032V烧写CPLD程序)。
2. Uboot烧写
Uboot的烧写比较简单,采用烧录器将Uboot程序下载到SPIflash中即可。
在烧写时请注意以下几点:
(1)要确保烧录器选择的芯片型号与实际被烧写的芯片型号保持一致;
(2)已焊接过的SPIflash芯片需要使用洗板水清晰管脚上的松香,防止管脚与芯片座接触不良;
(3)为了确保二进制程序正确烧入芯片内,可以使用烧程软件读出被烧写的程序并与原始程序对比,如果内容一致则烧录成功;
在交换机使用Uboot进行硬件资源引导时,必须先确保I2C和CPLD已烧写正确程序,否则CPU无法正常工作,串口无如何信息输出。
3. 内核烧写
(1)将“ubifs_arm10.image”文件复制到FAT或FAT32格式的U盘,把该U盘插入板上的USB接口。
给开发板上电,当出现“Hit any key to stop autoboot”提示时,敲击键盘任意键并出现“Marvell>> ”,串口显示如下:
BootROM 1.41 Booting from SPI flash General initialization - Version: 1.0.0 Serdes initialization - Version: 1.0.2 mvCtrlPexPolaritySet: TWSI Write failed, leaving PEX polarity in EP mode PEX: pexIdx 0, detected no link mvCtrlPexPolaritySet: TWSI Write failed, leaving PEX polarity in EP mode PEX: pexIdx 0, detected no link mvCtrlPexPolaritySet: TWSI Write failed, leaving PEX polarity in EP mode PEX: pexIdx 0, detected no link DDR3 Training Sequence - Ver TIP-1.22.0 mvHwsBoardIdGet: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window Updated Physical Mem size is from 0x20000000 to 10000000 DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ 4000 ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-01788-g1ebef39 (Nov 10 2014 - 13:58:38) Marvell version: 2014_T3.0p2 Board: RD-XC3-24G-4SFPRD-XC3-24G-4SFP SoC: Alleycat3 CPU: Marvell PJ4B (584) v7 (Rev 2) LE CPU @ 800 [MHz] L2 @ 200 [MHz] TClock @ 200 [MHz] DDR @ 400 [MHz] DDR 16Bit Width, FastPath Memory Access, DLB Enabled DDR ECC Disabled DRAM: 512 MiB Map: Code: 0x1fed3000:0x1ff96258 BSS: 0x1ffef43c Stack: 0x1f9c2ef0 Heap: 0x1f9c3000:0x1fed3000 NAND: 1024 MiB MMC: MRVL_MMC: 0 SF: Detected MX25L25735E with page size 64 KiB, total 32 MiB PCI-e 0: Detected No Link. FPU initialized to Run Fast Mode. USB2.0 0: Host Mode Net: | port | Interface | PHY address | |--------|-----------|--------------| No ethernet found. Hit any key to stop autoboot: 0 Marvell>>
(2)在串口中输入“nand erase.chip”,对NANDflash进行擦除操作!
Marvell>> nand erase.chip
NAND erase.chip: device 0 whole chip Bad block table not found for chip 0 Bad block table not found for chip 0 Bad block table written to 0x00003ff80000, version 0x01 Bad block table written to 0x00003ff00000, version 0x01 Skipping bad block at 0x3fc00000 Skipping bad block at 0x3fc80000 Skipping bad block at 0x3fd00000 Skipping bad block at 0x3fd80000 Skipping bad block at 0x3fe00000 Skipping bad block at 0x3fe80000 Skipping bad block at 0x3ff00000 Skipping bad block at 0x3ff80000 OK Marvell>>(3)识别USB,在串口输入“usb start”。
Marvell>> usb start
(Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 2) : USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Marvell>>(4)向NANDflash烧写内核文件,在串口输入“mtdburn usb 0 FAT ubifs_arm10.image NAND”,在烧写的过程中会出现两次选择提示,全部输入“y”并回车。
Marvell>> mtdburn usb 0 FAT ubifs_arm10.image NAND
Marvell>> mtdburn usb 0 FAT ubifs_arm10.image NAND - Load from device : usb, Interface :0 - File System : FAT - Filename : ubifs_arm10.image - Flash destination : NAND
Do you want to continue ? [Y/n] y
(Re)start USB... USB0: Port (usbActive) : 0 Interface (usbType = 2) : USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found reading ubifs_arm10.image Trying separation of kernel/vxWorks-image and root_fs. Work areas=0x06000000,0x07000000 kernel separation ended ok. unc_len=2767504, total_in=2772111 rootfs separation ended ok. unc_len=23068672, total_in=12952525 Burning kernel on flash at 0x00000000, length=2702K Erasing 0x0 - 0xa00000: (10MB) nand erase 0 a00000 NAND erase: device 0 offset 0x0, size 0xa00000 Erasing at 0x980000 -- 100% complete. OK [Done] Copy to Flash nand write.trimffs 6000000 0 2a3a90 NAND write: device 0 offset 0x0, size 0x2a3a90 2767504 bytes written: OK Erasing 0xa00000 - 0x2a00000: (32MB) nand erase a00000 2000000 NAND erase: device 0 offset 0xa00000, size 0x2000000 Erasing at 0x2980000 -- 100% complete. OK Burning rootfs on flash at 0x00a00000, length=22528K Copy to Flash nand write.trimffs 7000000 a00000 1600000 NAND write: device 0 offset 0xa00000, size 0x1600000 23068672 bytes written: OKDo you want to prepare CPSS environment variables (mtdparts & bootcmd) ? [y/N]
Do you want to continue ? [Y/n] y
Saving cpss environment variable mtdparts = 'spi_flash:2m(spi_uboot)ro,4m(spi_kernel),16m(spi_rootfs),-(remainder);armada-nand:10m(nand_kernel),-(nand_rootfs)' standalone_mtd_spi = sf probe; sf read ${loadaddr} 0x200000 0x400000; setenv bootargs ${console} root=/dev/mtdblock2 rw init=/linuxrc rootfstype=jffs2 rootwait mtdparts=${mtdparts} ${mvNetConfig}; bootm ${loadaddr} standalone_mtd = nand read ${loadaddr} 0x0 0xa00000; setenv bootargs ${console} mtdparts=${mtdparts} ubi.mtd=5 root=ubi0:rootfs_nand ro rootfstype=ubifs ${mvNetConfig}; bootm 0x2000000; Saving Environment to SPI Flash... SF: Detected MX25L25735E with page size 64 KiB, total 32 MiB Erasing SPI flash....Writing to SPI flash.....done boot command prepared: run 'boot' to load kernel and file system from flash. Marvell>>(5)启动交换机系统,向串口输入“boot”。
Marvell>> boot
NAND read: device 0 offset 0x0, size 0xa00000 10485760 bytes read: OK ## Booting kernel from Legacy Image at 02000000 ... Image Name: Linux-3.4.69 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2767440 Bytes = 2.6 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Lin done, booting thBooting Linux on physical CPU 0 Linux version 3.4.69 (yedidiaf@vvenus173) (gcc version 4.6.4 20120731 (prerelease) (Marvell GCC 201502-1645.aee66e26 CVE-2015-0235) ) #1 SMP Wed Oct 28 20:22:26 IST 2015 CPU: Marvell PJ4Bv7 Processor [562f5842] revision 2 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache Machine: Marvell BC2 RD Using UBoot passing parameters structure Memory policy: ECC disabled, Data cache writealloc BUG: mapping for 0xfc000000 at 0xff400000 out of vmalloc space SMP: init cpus PERCPU: Embedded 7 pages/cpu @c09cf000 s5952 r8192 d14528 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyS0,115200 mtdparts=spi_flash:2m(spi_uboot)ro,4m(spi_kernel),16m(spi_rootfs),-(remainder);armada-nand:10m(nand_kernel),-(nand_rootfs) ubi.mtd=5 root=ubi0:rootfs_nand ro rootfstype=ubifs mv_net_config=4,(00:50:43:11:11:11,0:1:2:3),mtu=1500 PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 512MB = 512MB total Memory: 513784k/513784k available, 10504k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0519000 (5188 kB) .init : 0xc0519000 - 0xc0549740 ( 194 kB) .data : 0xc054a000 - 0xc05806c0 ( 218 kB) .bss : 0xc05806e4 - 0xc05cafd8 ( 299 kB) Hierarchical RCU implementation. NR_IRQS:178 Initializing MSYS SOC Timer 0 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 SMP: prepare CPUs (2 cores) Setting up static identity map for 0x3edd50 - 0x3edd70 SMP: CPU 0 Waking up CPU 1 CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (1590.88 BogoMIPS). devtmpfs: initialized NET: Registered protocol family 16 Aurora: Working in ARMv7 mode L0 cache Enabled Speculative Prefetch Disabled Aurora L2 Cache Enabled Support IO coherency. CPU Interface ------------- SDRAM_CS0 ....base 000000000, size 512MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable DEVICE_CS0 ....base 0f2200000, size 1MB DEVICE_CS1 ....no such DEVICE_CS2 ....no such DEVICE_CS3 ....no such PEX0_MEM ....base 090000000, size 128MB PEX0_IO ....no such INTER_REGS ....base 0f1000000, size 1MB DFX_INTER_REGS ....base 0fc000000, size 1MB SWITCH_REGS ....base 0f8000000, size 64MB DMA_UART ....no such SPI_CS0 ....base 0f6000000, size 32MB SPI_CS1 ....no such SPI_CS2 ....no such SPI_CS3 ....no such SPI_CS4 ....no such SPI_CS5 ....no such SPI_CS6 ....no such SPI_CS7 ....no such BOOT_ROM_CS ....base 0fff00000, size 1MB DEV_BOOTCS ....base 0f4000000, size 32MB USB_REGS ....no such DRAGONITE ....base 080000000, size 128MB Marvell MSYS RD-XC3-24G-4SFP Board - Soc: BobK Rev A1 LE Detected Tclk 200000000, SysClk 167000000, FabricClk 200000000, PClk 800000000 LSP version: linux-3.4.69-2014_T2.1p13 Register platform device: mv_neta_port_0 Register platform device: mv_neta_port_1 registered dev#0 asa ehci_marvell Marvell USB EHCI Host controller #0: df8a3dc0 bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource msys_clocksource NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 5, 131072 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI-E: Checking physical bus #0 (controller #0): Enabled - No Link SoC: model = 0xf400, revision = 0x4 o 2 Giga ports supported o SKB recycle supported (Enabled) o NETA acceleration mode 1 o RX Queue support: 8 Queues * 128 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Driver INFO statistics enabled port #0: is_sgmii=1, is_rgmii=0, phy_addr=-1 o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o eth0, ifindex = 2, GbE port = 0 giga p=0: mtu=1500, mac=00:0e:c6:00:2d:72 (platform) port #1: is_sgmii=1, is_rgmii=0, phy_addr=-1 o Loading network interface(s) for port #1: cpu_mask=0x3, tx_csum_limit=9800 o Port 1 is connected to Linux netdevice o eth1, ifindex = 3, GbE port = 1 giga p=1: mtu=1500, mac=00:50:43:7b:7b:7b (platform) Phy-driver: Initialization started Phy-driver: register_device() is called. Phy-driver: registered character device with major number = 217 and minor numbers 0...255 Warning CESA engine is powered Off dragonite_xcat dragonite_xcat.0: Initializing Co-processor... dragonite_xcat dragonite_xcat.0: Initializing Co-processor finished gpiochip_add: registered GPIOs 0 to 67 on device: mv_gpio jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 1003 io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy ) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 41) is a 16550A console [ttyS0] enabled loop: module loaded SPI Serial flash detected @ 0xf6000000, 32768KB (512sec x 64KB) 4 cmdlinepart partitions found on MTD device spi_flash Creating 4 MTD partitions on "spi_flash": 0x000000000000-0x000000200000 : "spi_uboot" 0x000000200000-0x000000600000 : "spi_kernel" 0x000000600000-0x000001600000 : "spi_rootfs" 0x000001600000-0x000002000000 : "remainder" armada-nand armada-nand.0: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC NAND device: Manufacturer ID: 0x2c, Chip ID: 0x38 (Micron NAND 1GiB 3,3V 8-bit) Bad block table found at page 262016, version 0x01 Bad block table found at page 261888, version 0x01 2 cmdlinepart partitions found on MTD device armada-nand 2 cmdlinepart partitions found on MTD device armada-nand Creating 2 MTD partitions on "armada-nand": 0x000000000000-0x000000a00000 : "nand_kernel" 0x000000a00000-0x000040000000 : "nand_rootfs" UBI: attaching mtd5 to ubi0 UBI: physical eraseblock size: 524288 bytes (512 KiB) UBI: logical eraseblock size: 516096 bytes UBI: smallest flash I/O unit: 4096 UBI: VID header offset: 4096 (aligned 4096) UBI: data offset: 8192 UBI: max. sequence number: 0 UBI: volume 0 ("rootfs_nand") re-sized from 42 to 1996 LEBs UBI: attached mtd5 to ubi0 UBI: MTD device name: "nand_rootfs" UBI: MTD device size: 1014 MiB UBI: number of good PEBs: 2020 UBI: number of bad PEBs: 8 UBI: number of corrupted PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 2020 UBI: number of PEBs reserved for bad PEB handling: 20 UBI: max/mean erase counter: 1/0 UBI: image sequence number: 74909680 UBI: background thread "ubi_bgt0d" started, PID 355 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI e100: Copyright(c) 1999-2006 Intel Corporation e1000e: Intel(R) PRO/1000 Network Driver - 1.9.5-k e1000e: Copyright(c) 1999 - 2012 Intel Corporation. sky2: driver version 1.30 PPP generic driver version 2.4.2 NET: Registered protocol family 24 pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver usbcore: registered new interface driver pegasus usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver net1080 usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus usbcore: registered new interface driver cdc_ncm ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_marvell ehci_marvell.0: Marvell Orion EHCI ehci_marvell ehci_marvell.0: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.0: irq 45, io base 0xfb050100 ehci_marvell ehci_marvell.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mousedev: PS/2 mouse device common for all mice i2c /dev entries driver mmc0: mvsdio driver initialized, lacking card detect (fall back to polling) usbcore: registered new interface driver usbhid usbhid: USB HID core driver oprofile: hardware counters not available oprofile: using timer interrupt. TCP: cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 ==Start PCI Devices scan and configure== ==Start Internal Devices scan and configure== prestera_device prestera_device.0: Internal device 0xf400 detected mvPP driver initialized prestera_device prestera_device.0: finish internal dev f400 probe drivers/rtc/hctosys.c: unable to op f9f9 en rtc device (rtc0) usb 1-1: new high-speed USB device number 2 using ehci_marvell UBIFS: mounted UBI device 0, volume 0, name "rootfs_nand" UBIFS: mounted read-only UBIFS: file system size: 1024966656 bytes (1000944 KiB, 977 MiB, 1986 LEBs) UBIFS: journal size: 10452992 bytes (10208 KiB, 9 MiB, 21 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 23 bytes (0 KiB) VFS: Mounted root (ubifs filesystem) readonly on device 0:13. devtmpfs: mounted Freeing init memory: 192K scsi0 : usb-storage 1-1:1.0 mount: Mounting none on /dev/pts failed: No such file or directory Wed Oct 28 20:21:00 UTC 2015 Linux MARVELL_LINUX 3.4.69 #1 SMP Wed Oct 28 20:22:26 IST 2015 Welcome to Embedded Linux _ _ | ||_| | | _ ____ _ _ _ _ | || | _ \| | | |\ \/ / | || | | | | |_| |/ \ |_||_|_| |_|\____|\_/\_/ On Marvell's ARMADAXP board For further information on the Marvell products check: http://www.marvell.com/ toolchain=mv7sft little endian Enjoy! scsi 0:0:0:0: Direct-Access Kingston DataTraveler 3.0 PMAP PQ: 0 ANSI: 6 sd 0:0:0:0: [sda] 30497664 512-byte logical blocks: (15.6 GB/14.5 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] No Caching mode page found sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] No Caching mode page found sd 0:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 0:0:0:0: [sda] No Caching mode page found sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Attached SCSI removable disk mvPP opened Starting System Root Taskcommander: threads are running: luaCLI cmdShell Supported boards: +---------------------------------+-------------------------+ | Board name | Revisions | +---------------------------------+-------------------------+ | 01 - DB-DX241-24G | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 02 - RD-DX246-24G | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 03 - RD-88E6183 | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 04 - DB-88E6093 | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 05 - RD-88E6093-24F4G | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 06 - DB-DX160-16G | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 07 - DB-DX270-24G-3XG | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 08 - RD-DX270-48G-2XG | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 09 - RD-DX241-48G | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 10 - RD-88E6093-484F4G | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 11 - DB-DX246-24G-3XG | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 12 - 24F4G | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 13 - DB-DX107-88E6095-48F2G | | | | 01 - Rev 0.1 | | | 02 - Rev 0.2 | +---------------------------------+-------------------------+ | 14 - DB-DX285-24G-4XG | | | | 01 - Rev 0.1 | | | 02 - Rev 0.2 - Vr Support| | | 03 - Rev 0.3 - FC OFF | | | 04 - Rev 0.4 - Ch2 as multiplexer| +---------------------------------+-------------------------+ | 15 - DB-DX106-10G | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 16 - DB-DX106-88E6095-48F2G | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 17 - DB-DX285-48G-4XG | | | | 01 - Rev 0.1 | | | 02 - Rev 0.2 - RD-DX285 | | | 03 - Rev 0.3 - FC OFF | +---------------------------------+-------------------------+ | 18 - DB-DX3-GP | | | | 01 - Rev 0.1 | | | 02 - Rev 0.2 - RDE tests| | | 03 - Rev 0.3 - FC OFF | +---------------------------------+-------------------------+ | 19 - xCat, xCat2, xCat3 | | | | 01 - Rev 0.1 | | | 02 - Rev 0.2 - SDMA | | | 03 - Rev 0.3 - FC OFF | | | 04 - Rev 0.4 - PBR | | | 05 - Rev 0.5 - P24/25 SGMII mode, p26/27 QX mode| | | 06 - Rev 0.6 - PBR SDMA | | | 07 - Rev 0.7 - SMI only board| | | 08 - Rev 0.8 - Native MII| | | 09 - Rev 0.9 - PHYMAC | | | 10 - Rev 0.10 - Legacy VPLS Enabled| | | 11 - Rev 0.11 - +Linux BM kernel driver| +---------------------------------+-------------------------+ | 20 - Lion | | | | 01 - Rev 0.1 | | | 02 - Rev 0.2 - performance test configuration| | | 03 - Rev 0.3 | | | 04 - Rev 0.4 | | | 05 - Rev 0.5 - RD-48 | | | 06 - Rev 0.6 - 98DX5198 all ports 1000BaseX| | | 07 - Rev 0.7 - 98DX5198 all ports SGMII 1G| | | 08 - Rev 0.8 - 98CX8203 2 core {0,1}| | | 09 - Rev 0.9 - RD-48 PQ3 (lion_mpc8544)| | | 10 - Rev 0.10- MII interface| | | 12 - Rev 0.12- RD-48 with solarflare PHY| | | 22 - multi port group FDB lookup| | | 24 - multi port group FDB lookup : 128K mode - auto init| | | 25 - multi port group FDB lookup : 64K mode - auto init| | | 26 - | +---------------------------------+-------------------------+ | 27 - Lion2 | | | | 01 - Rev 0.1 - 96X10G_SR_LR| | | 02 - Rev 0.2 - 32X40G_SR_LR| | | 03 - Rev 0.3 - 96X10G_KR| | | 04 - Rev 0.4 - 32X40G_KR4| | | 05 - Rev 0.5 - CT 10G 40G loopback Port| | | 06 - Rev 0.6 - 56X10G 210MHz| | | 07 - HooperRD:0..7-10G_KR;8...-40G_KR| | | 08 - HooperRD:0..7-10G_KR;8...-40G_KR: kernel driver| | | 10 - Rev 0.10- MII interface| | | 11 - 96X10G_SR_LR, PFC enable TC5_6 all ports| | | 12 - 96X10G_SR_LR, Lion2-4 cores | | | 22 - multi port group FDB lookup| | | 24 - multi port group FDB lookup : 256K mode - auto init| | | 25 - multi port group FDB lookup : 128K mode - auto init| | | 26 - 360MHz 0,1,2,3x10G 4,8,9x40G| | | 27 - | +---------------------------------+-------------------------+ | 28 - Lion3 | | | | 01 - Rev 0.1 | | | 02 - Rev 0.2 - implement FDB Cuckoo algorithm| +---------------------------------+-------------------------+ | 29 - BobCat2 | | | | 01 - Rev 0.1 | | | 02 - Rev 0.2 - TM enabled| | | 03 - Rev 0.3 -MTL RD board 48GE +4X10G| | | 04 - Rev 0.4 -MTL RD board 4*10G +2X40G->10G TM Enable| | | 05 - Simplified Init DB board| | | 06 - Simplified Init DB board - TM Enabled| | | 11 - Rev 0.11 RD Board | | | 12 - Rev 0.12 RD Board TM Enabled| +---------------------------------+-------------------------+ | 30 - Six BobCat2 | | | | 01 - Rev 0.1 | +---------------------------------+-------------------------+ | 31 - Two Lion2 + Bobcat2 | | | | 01 - Rev 0.1 - only Two Lion2| | | 02 - Rev 0.2 | | | 03 - Rev 0.3 - Two Hoopers + Bobcat2| | | 04 - Rev 0.4 - One Hooper + Bobcat2| +---------------------------------+-------------------------+ Call cpssInitSystem(index,boardRevId,reloadEeprom), where: index - The index of the system to be initialized. boardRevId - The index of the board revision. reloadEeprom - Whether the device's eeprom should be reloaded after start-init. CPSS Version Stream: CPSS_4.1_502 SW_INFRA_HWSERVICES_4.1_106 Cpss DxCh version: CPSS 4.1.12 LSP version: LSP version: linux-3.4.69-2014_T2.1p13 *************************************** Prestera commander shell server ready *************************************** Memory used by Lua 5515460 nChunks=63117 LUA CLI based on LUA 5.1 from www.lua.org LUA CLI uses Mini-XML engine from www.minixml.org *************************************************** LUA CLI shell ready *************************************************** Console#
(6)交换机系统测试
通过向串口写入命令“cpssInitSystem 19,2,0”配置交换机进行端口功能测试,如果测试结束后串口输出“Init system returned:0”,说明系统已被正确的初始化!
Console# cpssInitSystem 19,2,0
Console# cpssinitsystem 19,2,0 bspPciGetIntVec (single) int vector 0x21, internal Int 0x0 bspPciGetIntVec (single) int vector 0x21, internal Int 0x0 Device[0] ID 0xF40011AB revision A1 Core clock = 167Mhz Allocating 32784 bytes for DMA Allocating 32784 bytes for DMA Allocating 32000 bytes for DMA Allocating 3200 bytes for DMA Allocating 309601 bytes for DMA Allocating 45232 bytes for DMA Allocating 45232 bytes for DMA Warning:Tried to allocate 8388608 which is bigger than the memory chunk size. [UTF]: utfInit: ************************ [UTF]: prvUtfExtrasInit: PP dev [0], phy ports [28], virt ports [64] ports bmp[0x0fffffff] UTF: used port type [PRV_TGF_28_PORT_DEVICE_TYPE_E] , with ports up to[28] [UTF]: utfInit: OK, number of tests [3562] Run utfHelp 0 for help about UTF usage [UTF]: utfInit: ************************ [UTF]: utfHelp: **************************** *****UTF functions:***** utfHelp - to log a help about the function. utfTestsList - to log list of all configured (available) suits and tests. utfTestsTypeList - to log list of all configured suits by given UT type list (generic, enhanced, etc.) utfTestsRun - to run suits and tests utfTestsTypeRun - to run all UT by given UT type list (generic, enhanced, etc.) utfLogOutputSelect - to change output log mode (all, final, file, debug) utfLogOpen - to open logger with defined file name utfLogClose - to close logger utfRandomRunModeSet - to set test's random run mode utfTestRunFirstSet - to put specific test to be run first *****Examples:***** utfHelp 0 - to printout this help info. utfHelp "utfTestsList" - to get detailed info about command "utfTestsList" utfTestsList 0 - to log list of all configured (available) suits. utfTestsList "tgfBridge" - to log list of test cases inside suit "tgfBridge". utfTestsTypeList 6, 0 - to log list of all Enhanced UTs utfTestsTypeList 1, 6, 0 - to log list of all Generic and Enhanced UTs utfTestsRun 0, 1, 1 - to run all suits once with no interrupts after first failure utfTestsRun "tgfBridge",1,1 - to run all tests from suit "tgfBridge" once utfTestsRun "tgfBridge.tgfBasicDynamicLearning",1,1 - to run test "tgfBasicDynamicLearning" from suit "tgfBridge" once utfTestsRun ".tgfBasicDynamicLearning",1,1 - to run test "tgfBasicDynamicLearning" once utfTestsRun "tgfBridge-tgfIp",1,0 - to run all tests in a range between suits utfTestsRun "suit1.test1-suit2.test2",1,0 - to run a range of tests starting from certain test to certain test utfTestsRun "suit1-suit2.test",1,0 - to run a range of tests starting from certain suit to certain test utfTestsTypeRun 1, 1, 6, 0 - to run all Enhanced UT utfTestsTypeRun 1, 1, 1, 6, 0 - to run all Generic and Enhanced UT utfLogOutputSelect 0 - to change output log to serial utfLogOutputSelect 1 - to change output log to only final report utfLogOutputSelect 2 - to change output log to file utfLogOutputSelect 3 - to change output log to debug utfLogOpen "results.log" - to set logger into file "results.log" utfLogClose - to close opened logger utfRandomRunModeSet 1, 5 - to enable random run mode with seed 5 for random generator utfTestRunFirstSet "tgfBasicDynamicLearning" - to run "tgfBasicDynamicLearning" test first prvUtfSkipLongTestsFlagSet 1 - to state that when running tests skip those with 'long execution time' Run utfHelp "utfTestsList" for example to get detailed info about command [UTF]: utfHelp: **************************** [UTF]: utfInit: enh-UT : tested ports are : 0 8 18 23 cpssInitSystem time: 0 sec., 325479939 nanosec. Time processing the cpssInitSystem (from 'phase1 init') is [0] seconds + [322038232] nanoseconds Init system returned:0 devices, ports to be used by LUA tests , and configuration files ==> { { dev=0, port={ 0, 8, 18, 24, 20, 2 }, portCPU=63 } } Default PCL CFG Table Access mode configured on dev: 0 Console#
4.内核烧写VB脚本程序
说明:
(1)程序类型:Visual Basic脚本语言
(2)配套软件:SecureCRT 5.2.2
(3)交换机CPU型号:98DX3236
#$language = "VBScript" #$interface = "1.0" '------------------------------------------------- 'name: burn_image.vbs 'date: 20170928 'Email: snaking616@163.com '------------------------------------------------- crt.Screen.Synchronous = True ' This automatically generated script may need to be ' edited in order to work correctly. Sub Main crt.Screen.Send "nand erase.chip" & chr(13) crt.Screen.WaitForString "Marvell>>" crt.Screen.Send "usb start" & chr(13) crt.Screen.WaitForString "Marvell>>" ' crt.Screen.Send "mtdburn usb 0 FAT jffs2_arm.image NAND" & chr(13) crt.Screen.Send "mtdburn usb 0 FAT ubifs_arm10.image NAND" & chr(13) crt.Screen.WaitForString "Do you want to continue ? [Y/n]" crt.Screen.Send "y" & chr(13) crt.Screen.WaitForString "Do you want to continue ? [Y/n]" crt.Screen.Send "y" & chr(13) crt.Screen.WaitForString "Marvell>>" crt.Screen.Send "boot" & chr(13) End Sub
相关文章推荐
- 将内存中的内核烧写到nandflash中;通过串口下载内核和文件系统
- nand烧写分析/内核在启动过程中式如何将这个文件映射成/目录及各子目录的?
- arm下如何烧写指定分区大小的内核和文件系统
- arm下如何烧写指定分区大小的内核和文件系统
- 【Android 系统开发】 编译 Android文件系统 u-boot 内核 并烧写到 OK-6410A 开发板上
- 内核和文件系统的烧写和启动配置
- 烧写文件系统和内核
- 烧写内核文件
- 【Android 系统开发】 编译 Android文件系统 u-boot 内核 并烧写到 OK-6410A 开发板上
- 1.移植3.4内核-分析内核启动过程,重新分区,烧写jffs2文件系统
- Android内核开发:系统分区与镜像文件的烧写
- Android内核开发:系统分区与镜像文件的烧写
- uboot从SD卡烧写内核和文件系统
- 【Android 系统开发】 编译 Android文件系统 u-boot 内核 并烧写到 OK-6410A 开发板上
- 如何用nfs命令烧写内核和文件系统(网络下载文件到nandflash)(未完)
- 嵌入式linux 内核和根文件系统烧写方式简介
- Linux系统下用dnw烧写JZ2440开发板的内核及文件系统
- arm7开发板烧写内核、文件系统,交叉编译hello world
- 思考mysql内核之初级系列6---innodb文件管理
- 如何用nfs命令烧写内核和文件系统(网络下载文件到nandflash)(未完)