uboot bd_info
2017-03-16 08:27
239 查看
include/asm-generic/u-boot.h
bd_info:
/*
* Board information passed to Linux kernel from U-Boot
*
* include/asm-ppc/u-boot.h
*/
#ifndef __ASSEMBLY__
typedef struct bd_info {
unsigned long bi_memstart; /* start of DRAM memory */
phys_size_t bi_memsize; /* size of DRAM memory in bytes */
unsigned long bi_flashstart; /* start of FLASH memory */
unsigned long bi_flashsize; /* size of FLASH memory */
unsigned long bi_flashoffset; /* reserved area for startup monitor */
unsigned long bi_sramstart; /* start of SRAM memory */
unsigned long bi_sramsize; /* size of SRAM memory */
#ifdef CONFIG_AVR32
unsigned char bi_phy_id[4]; /* PHY address for ATAG_ETHERNET */
unsigned long bi_board_number;/* ATAG_BOARDINFO */
#endif
#ifdef CONFIG_ARM
unsigned long bi_arm_freq; /* arm frequency */
unsigned long bi_dsp_freq; /* dsp core frequency */
unsigned long bi_ddr_freq; /* ddr frequency */
#endif
#if defined(CONFIG_5xx) || defined(CONFIG_8xx) || defined(CONFIG_MPC8260) \
|| defined(CONFIG_E500) || defined(CONFIG_MPC86xx)
unsigned long bi_immr_base; /* base of IMMR register */
#endif
#if defined(CONFIG_MPC5xxx) || defined(CONFIG_M68K)
unsigned long bi_mbar_base; /* base of internal registers */
#endif
#if defined(CONFIG_MPC83xx)
unsigned long bi_immrbar;
#endif
unsigned long bi_bootflags; /* boot / reboot flag (Unused) */
unsigned long bi_ip_addr; /* IP Address */
unsigned char bi_enetaddr[6]; /* OLD: see README.enetaddr */
unsigned short bi_ethspeed; /* Ethernet speed in Mbps */
unsigned long bi_intfreq; /* Internal Freq, in MHz */
unsigned long bi_busfreq; /* Bus Freq, in MHz */
#if defined(CONFIG_CPM2)
unsigned long bi_cpmfreq; /* CPM_CLK Freq, in MHz */
unsigned long bi_brgfreq; /* BRG_CLK Freq, in MHz */
unsigned long bi_sccfreq; /* SCC_CLK Freq, in MHz */
unsigned long bi_vco; /* VCO Out from PLL, in MHz */
#endif
#if defined(CONFIG_MPC512X)
unsigned long bi_ipsfreq; /* IPS Bus Freq, in MHz */
#endif /* CONFIG_MPC512X */
#if defined(CONFIG_MPC5xxx) || defined(CONFIG_M68K)
unsigned long bi_ipbfreq; /* IPB Bus Freq, in MHz */
unsigned long bi_pcifreq; /* PCI Bus Freq, in MHz */
#endif
#if defined(CONFIG_EXTRA_CLOCK)
unsigned long bi_inpfreq; /* input Freq in MHz */
unsigned long bi_vcofreq; /* vco Freq in MHz */
unsigned long bi_flbfreq; /* Flexbus Freq in MHz */
#endif
#if defined(CONFIG_405) || \
defined(CONFIG_405GP) || \
defined(CONFIG_405EP) || \
defined(CONFIG_405EZ) || \
defined(CONFIG_405EX) || \
defined(CONFIG_440)
unsigned char bi_s_version[4]; /* Version of this structure */
unsigned char bi_r_version[32]; /* Version of the ROM (AMCC) */
unsigned int bi_procfreq; /* CPU (Internal) Freq, in Hz */
unsigned int bi_plb_busfreq; /* PLB Bus speed, in Hz */
unsigned int bi_pci_busfreq; /* PCI Bus speed, in Hz */
unsigned char bi_pci_enetaddr[6]; /* PCI Ethernet MAC address */
#endif
#ifdef CONFIG_HAS_ETH1
unsigned char bi_enet1addr[6]; /* OLD: see README.enetaddr */
#endif
#ifdef CONFIG_HAS_ETH2
unsigned char bi_enet2addr[6]; /* OLD: see README.enetaddr */
#endif
#ifdef CONFIG_HAS_ETH3
unsigned char bi_enet3addr[6]; /* OLD: see README.enetaddr */
#endif
#ifdef CONFIG_HAS_ETH4
unsigned char bi_enet4addr[6]; /* OLD: see README.enetaddr */
#endif
#ifdef CONFIG_HAS_ETH5
unsigned char bi_enet5addr[6]; /* OLD: see README.enetaddr */
#endif
#if defined(CONFIG_405GP) || defined(CONFIG_405EP) || \
defined(CONFIG_405EZ) || defined(CONFIG_440GX) || \
defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \
defined(CONFIG_460EX) || defined(CONFIG_460GT)
unsigned int bi_opbfreq; /* OPB clock in Hz */
int bi_iic_fast[2]; /* Use fast i2c mode */
#endif
#if defined(CONFIG_4xx)
#if defined(CONFIG_440GX) || \
defined(CONFIG_460EX) || defined(CONFIG_460GT)
int bi_phynum[4]; /* Determines phy mapping */
int bi_phymode[4]; /* Determines phy mode */
#elif defined(CONFIG_405EP) || defined(CONFIG_405EX) || defined(CONFIG_440)
int bi_phynum[2]; /* Determines phy mapping */
int bi_phymode[2]; /* Determines phy mode */
#else
int bi_phynum[1]; /* Determines phy mapping */
int bi_phymode[1]; /* Determines phy mode */
#endif
#endif /* defined(CONFIG_4xx) */
ulong bi_arch_number; /* unique id for this board */
ulong bi_boot_params; /* where this board expects params */
#ifdef CONFIG_NR_DRAM_BANKS
struct { /* RAM configuration */
phys_addr_t start;
phys_size_t size;
} bi_dram[CONFIG_NR_DRAM_BANKS];
#endif /* CONFIG_NR_DRAM_BANKS */
} bd_t;
#endif /* __ASSEMBLY__ */
相关文章推荐
- U-Boot学习:[0]global_data 和 bd_info
- bootinfo
- AIX bootinfo命令
- U-boot的gd_t和bd_t数据结构简介
- OK6410 uboot1.1.16的board.c相关函数分析(关键数据结构(gd_t和bd_t))
- u-boot分析——struct gd_t与struct bd_t
- u-boot分析——struct gd_t与struct bd_t
- u-boot分析——struct gd_t与struct bd_t
- Spring Boot中使用Actuator的/info端点输出Git版本信息
- spring-boot-starter-actuator /info获取空信息
- u-boot分析——struct gd_t与struct bd_t
- 使用spring-boot-starter-actuator http://localhost:8080/info无法获取到相应信息
- AIX bootinfo命令
- 移植uip-0.9到u-boot中出现undefined reference to `flash_info'错误的分析过程
- 【转】U-BOOT之五:gd_t和bd_t数据结构简介
- spring boot打包 部署 依赖 hc/info
- Spring Boot教程(十四)Spring Boot中使用Actuator的/info端点输出Git版本信息
- U-BOOT之五:gd_t和bd_t数据结构简介
- u-boot分析 之 struct gd_t与struct bd_t
- u-boot主要数据结构-- bd