linux下非标准波特率的设置和使用
2015-05-11 08:51
399 查看
通常,在linux下面,设置串口使用终端IO的相关函数设置,如tcsetattr等函数,linux内部有一个对常用波特率列表的索引,根据设置的波特率用底层驱动来设置异步通信芯片的寄存器
对于非标准的任意波特率需要用ioctl(fd, TIOCGSERIAL, p)和ioctl(fd, TIOCSSERIAL, p)的配合,ioctl的最后一个参数是struct serial_struct *类型,在linux/serial.h中定义。其中baud_base是基准晶振频率/16,通常是115200,你需要设的是custom_divisor这个值,最终的波特率为baud_base/custom_divisor,比如你需要28800,因为115200/4=28800,所以要设置custom_divisor=4,。
具体过程为,先设置波特率设为38400(tcsetattr),然后用TIOCGSERIAL得到当前的设置,将flags设置ASYNC_SPD_CUST位,设置custom_divisor,最后用TIOCSSERIAL设置。
使用setserial其实就是利用上述方法,来设置baud_base, custom_divisor等, 其内部实现就是使用ioctl来进行设置,
另外还可以用硬件更换晶振,根据比例来达到使用一些非标准的波特率的目的.
参考:http://blog.ednchina.com/seam_liu/7181/post.aspx
#include <termios.h>
#include <sys/ioctl.h>
#include <linux/serial.h>
struct serial_t {
int fd;
char *device;/*/dev/ttyS0,...*/
int baud;
int databit;/*5,6,7,8*/
char parity;/*O,E,N*/
int stopbit;/*1,2*/
int startbit;/*1*/
struct termios options;
};
//设置为特诉波特率,比如28800
int serial_set_speci_baud(struct serial_t *tty,int baud)
{
struct serial_struct ss,ss_set;
cfsetispeed(&tty->options,B38400);
cfsetospeed(&tty->options,B38400);
tcflush(tty->fd,TCIFLUSH);/*handle unrecevie char*/
tcsetattr(tty->fd,TCSANOW,&tty->options);
if((ioctl(tty->fd,TIOCGSERIAL,&ss))<0){
dprintk("BAUD: error to get the serial_struct info:%s\n",strerror(errno));
return -1;
}
ss.flags = ASYNC_SPD_CUST;
ss.custom_divisor = ss.baud_base / baud;
if((ioctl(tty->fd,TIOCSSERIAL,&ss))<0){
dprintk("BAUD: error to set serial_struct:%s\n",strerror(errno));
return -2;
}
ioctl(tty->fd,TIOCGSERIAL,&ss_set);
dprintk("BAUD: success set baud to %d,custom_divisor=%d,baud_base=%d\n",
baud,ss_set.custom_divisor,ss_set.baud_base);
return 0;
}
对于非标准的任意波特率需要用ioctl(fd, TIOCGSERIAL, p)和ioctl(fd, TIOCSSERIAL, p)的配合,ioctl的最后一个参数是struct serial_struct *类型,在linux/serial.h中定义。其中baud_base是基准晶振频率/16,通常是115200,你需要设的是custom_divisor这个值,最终的波特率为baud_base/custom_divisor,比如你需要28800,因为115200/4=28800,所以要设置custom_divisor=4,。
具体过程为,先设置波特率设为38400(tcsetattr),然后用TIOCGSERIAL得到当前的设置,将flags设置ASYNC_SPD_CUST位,设置custom_divisor,最后用TIOCSSERIAL设置。
使用setserial其实就是利用上述方法,来设置baud_base, custom_divisor等, 其内部实现就是使用ioctl来进行设置,
另外还可以用硬件更换晶振,根据比例来达到使用一些非标准的波特率的目的.
参考:http://blog.ednchina.com/seam_liu/7181/post.aspx
#include <termios.h>
#include <sys/ioctl.h>
#include <linux/serial.h>
struct serial_t {
int fd;
char *device;/*/dev/ttyS0,...*/
int baud;
int databit;/*5,6,7,8*/
char parity;/*O,E,N*/
int stopbit;/*1,2*/
int startbit;/*1*/
struct termios options;
};
//设置为特诉波特率,比如28800
int serial_set_speci_baud(struct serial_t *tty,int baud)
{
struct serial_struct ss,ss_set;
cfsetispeed(&tty->options,B38400);
cfsetospeed(&tty->options,B38400);
tcflush(tty->fd,TCIFLUSH);/*handle unrecevie char*/
tcsetattr(tty->fd,TCSANOW,&tty->options);
if((ioctl(tty->fd,TIOCGSERIAL,&ss))<0){
dprintk("BAUD: error to get the serial_struct info:%s\n",strerror(errno));
return -1;
}
ss.flags = ASYNC_SPD_CUST;
ss.custom_divisor = ss.baud_base / baud;
if((ioctl(tty->fd,TIOCSSERIAL,&ss))<0){
dprintk("BAUD: error to set serial_struct:%s\n",strerror(errno));
return -2;
}
ioctl(tty->fd,TIOCGSERIAL,&ss_set);
dprintk("BAUD: success set baud to %d,custom_divisor=%d,baud_base=%d\n",
baud,ss_set.custom_divisor,ss_set.baud_base);
return 0;
}
相关文章推荐
- linux下非标准波特率的设置和使用
- 剖析非标准波特率的设置和使用于Linux操作系统中
- linux设置非标准波特率200000bit/s
- 【Linux】 设置使用 sudo
- 使用crond 在linux中设置计划任务
- Linux中使用export命令设置环境变量
- Windows 和 Linux下使用socket下载网页页面内容(可设置接收/发送超时)的代码
- Linux的文件权限设置为什么可以使用421
- Linux使用_设置Tab键
- VNC、SSH远程连接Linux系统设置及常见使用问题
- Linux/UNIX下使用ssh-keygen设置SSH无密码登录
- 使用SecureCRT时屏幕僵死的处理方法――Linux终端设置技巧
- Linux/UNIX下使用ssh-keygen设置SSH无密码登录
- Linux:使用ulimit设置文件最大打开数<转>
- Linux无线网络设置--wpa_supplicant的使用
- Zabbix 使用Linux本机或外部邮箱实现邮件报警设置
- 使用SecureCRT对Linux vim进行颜色设置【可用的.vimrc文件内容】
- linux使用命令设置IP,DNS,网关
- 在64位linux上安装tomcat、jdk,及使用smb设置文件共享