MTK android lcm调试

参考MTK 文档LCM_Customer_document_MT6575.pdf

The following shows the steps to add a new LCM driver:

(1) Create LCM driver folder $LCM in alps/mediatek/custom/common/kernel/lcm/

(2) Create LCM driver source file $LCM.c in alps/mediatek/custom/common/kernel/lcm/$LCM

(3) Implement LCM driver and export lcm_driver_list/lcm_count variables.



Adaptive LCM Support

At first you should add you new lcm driver as listed in the previous section, and then add the

adaptive support:

1. Modify the adaptive lcm driver common file:

alps/mediatek/custom/common/kernel/lcm/mt65xx_lcm_list.c

2. Add the new LCM driver global variables as shown in the figure below:



3. [VERY IMPORTANT] Please delete the unused LCM driver folder in the customization folder,

such as shown in the figure below:



4. But what if I didn’t delete the folders un-usable? The code size will increase, because the

other LCM drivers will be compiled into codebase too; And if your project doesn’t define

GPIO usage for serial interface, there will be build error.

5. Modify the project makefile alps/mediate/config/(project)/ProjetConfig.mk

Modify CUSTOM_KERNEL_LCM=mt65xx

Modify CUSTOM_UBOOT_LCM=mt65xx

Case Study – DBI Interface LCM Driver Porting

In this chapter, we’ll go through a real case study of DBI LCM driver porting.

LCM specifications:

 LCM Drive IC: hx8369

 Interface: 24-bit 80 system bus interface

 LCD size: 480*800

1. Create LCM driver folder and LCM driver source file

alps/mediatek/custom/common/kernel/lcm/hx8369/lcm_dr.c

2. Modify the project makefile alps/mtk/make/$(project).mak

Add CUSTOM_KERNEL_LCM= hx8369

Add CUSTOM_UBOOT_LCM= hx8369

3. Fill the LCM parameters

A. Configure the basic information according to the HW connection, LCM type and LCM size:



MT6575 LCD IO selection is as shown in following table. LCD data pin can share between DPI and NAND data pin



For example, we use 24bits DBI interface LCM, and connect LCM data pin to MT6575 baseband

Pin DPIR[7:0], DPIG[7:0], DPIB[7:0]. So we must set io_select_mode to be 1; if connect LCM data

pin to Nand IF, we must set io_select_mode to be 0

B. Configure data format according to the RGB data pin assignment of the LCM datasheet



C. Configure LCM waveform timing according to the requirement specified in the LCM datasheet



Note: MT6575 LCD controller clock frequency is 130MHz, so clock cycle time is 1/130MHz = 7.69ns

4. Implement LCM init function

According the init process specified in LCM datasheet, pull down/up the reset pin, delay and set

LCM init register settings.

5. Implement LCM update function

Send the block update commands to LCM

6. Implement LCM suspend/resume functions

Send suspend/resume commands to LCM

7. Rebuild uboot and kernel

In the root directory:

./mk $(project) gen_cust

./mk $(project) remake uboot/kernel

./mk $(project) bootimage

参考代码：

[cpp] view
plaincopy

/*****************************************************************************

* Copyright Statement:

* --------------------

* This software is protected by Copyright and the information
contained

* herein is confidential. The software may not be copied
and the information

* contained herein may not be used or disclosed except
with the written

* permission of MediaTek Inc. (C) 2008

*

* BY OPENING THIS FILE, BUYER HEREBY UNEQUIVOCALLY ACKNOWLEDGES
AND AGREES

* THAT THE SOFTWARE/FIRMWARE AND ITS DOCUMENTATIONS ("MEDIATEK
SOFTWARE")

* RECEIVED FROM MEDIATEK AND/OR ITS REPRESENTATIVES ARE
PROVIDED TO BUYER ON

* AN "AS-IS" BASIS ONLY. MEDIATEK EXPRESSLY DISCLAIMS
ANY AND ALL WARRANTIES,

* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF

* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR
NONINFRINGEMENT.

* NEITHER DOES MEDIATEK PROVIDE ANY WARRANTY WHATSOEVER
WITH RESPECT TO THE

* SOFTWARE OF ANY THIRD PARTY WHICH MAY BE USED BY, INCORPORATED
IN, OR

* SUPPLIED WITH THE MEDIATEK SOFTWARE, AND BUYER AGREES
TO LOOK ONLY TO SUCH

* THIRD PARTY FOR ANY WARRANTY CLAIM RELATING THERETO.
MEDIATEK SHALL ALSO

* NOT BE RESPONSIBLE FOR ANY MEDIATEK SOFTWARE RELEASES
MADE TO BUYER'S

* SPECIFICATION OR TO CONFORM TO A PARTICULAR STANDARD
OR OPEN FORUM.

*

* BUYER'S SOLE AND EXCLUSIVE REMEDY AND MEDIATEK'S ENTIRE
AND CUMULATIVE

* LIABILITY WITH RESPECT TO THE MEDIATEK SOFTWARE RELEASED
HEREUNDER WILL BE,

* AT MEDIATEK'S OPTION, TO REVISE OR REPLACE THE MEDIATEK
SOFTWARE AT ISSUE,

* OR REFUND ANY SOFTWARE LICENSE FEES OR SERVICE CHARGE
PAID BY BUYER TO

* MEDIATEK FOR SUCH MEDIATEK SOFTWARE AT ISSUE.

*

* THE TRANSACTION CONTEMPLATED HEREUNDER SHALL BE CONSTRUED
IN ACCORDANCE

* WITH THE LAWS OF THE STATE OF CALIFORNIA, USA, EXCLUDING
ITS CONFLICT OF

* LAWS PRINCIPLES. ANY DISPUTES, CONTROVERSIES OR CLAIMS
ARISING THEREOF AND

* RELATED THERETO SHALL BE SETTLED BY ARBITRATION IN
SAN FRANCISCO, CA, UNDER

* THE RULES OF THE INTERNATIONAL CHAMBER OF COMMERCE
(ICC).

*

*****************************************************************************/

#include <linux/string.h>

#include "lcm_drv.h"

//#include <linux/kernel.h> //for printk()

//extern void printf(const char* fmt, ...);

#ifdef BUILD_UBOOT

#include <asm/arch/mt6575_gpio.h>

#define print(x...) printf(x)

#else

#include <mach/mt6575_gpio.h>

#define print(x...) printk(x)

#endif

//libin modify for M1-4 on 20120726

#define GPIO_LCD_RST 18 //GPIO18

#define GPIO_MODE_00 0

#define GPIO_DIR_OUT 1

#define GPIO_OUT_ONE 1

#define GPIO_OUT_ZERO 0

extern s32
mt_set_gpio_mode(u32 u4Pin, u32 u4Mode);

extern s32
mt_set_gpio_out(u32 u4Pin, u32 u4PinOut);

extern s32
mt_set_gpio_dir(u32 u4Pin, u32 u4Dir);

// ---------------------------------------------------------------------------

// Local Constants

// ---------------------------------------------------------------------------

#define FRAME_WIDTH (320)

#define FRAME_HEIGHT (480)

// ---------------------------------------------------------------------------

// Local Variables

// ---------------------------------------------------------------------------

static LCM_UTIL_FUNCS
lcm_util = {0};

#define SET_RESET_PIN(v) (lcm_util.set_reset_pin((v)))

#define UDELAY(n) (lcm_util.udelay(n))

#define MDELAY(n) (lcm_util.mdelay(n))

// ---------------------------------------------------------------------------

// Local Functions

// ---------------------------------------------------------------------------

static __inline
unsigned int HIGH_BYTE(unsigned int val)

{

return (val
>> 8) & 0xFF;

}

static __inline
unsigned int LOW_BYTE(unsigned int val)

{

return (val
& 0xFF);

}

static __inline void send_ctrl_cmd(unsigned int cmd)

{

//MDELAY(5);

//mt_set_gpio_out(16, GPIO_OUT_ZERO);

lcm_util.send_cmd(cmd);

// mt_set_gpio_out(16, GPIO_OUT_ONE);

}

static __inline void send_data_cmd(unsigned int data)

{

//MDELAY(5);

//mt_set_gpio_out(16, GPIO_OUT_ZERO);

lcm_util.send_data(data);

// mt_set_gpio_out(16, GPIO_OUT_ONE);

}

static __inline
unsigned int read_data_cmd()

{

return lcm_util.read_data();

}

static __inline void set_lcm_register(unsigned int regIndex,

unsigned int regData)

{

send_ctrl_cmd(regIndex);

send_data_cmd(regData);

}

static void init_lcm_registers(void)

{

send_ctrl_cmd(0xF1);

send_data_cmd(0x36);

send_data_cmd(0x04);

send_data_cmd(0x00);

send_data_cmd(0x3C);

send_data_cmd(0x0F);

send_data_cmd(0x8F);

send_ctrl_cmd(0xf2);

send_data_cmd(0x18);

send_data_cmd(0xa3);

send_data_cmd(0x12);

send_data_cmd(0x02);

send_data_cmd(0xb2);

send_data_cmd(0x12);

send_data_cmd(0xff);

send_data_cmd(0x10);

send_data_cmd(0x00);

send_ctrl_cmd(0xf8);

send_data_cmd(0x21);

send_data_cmd(0x04);

send_ctrl_cmd(0xf9);

send_data_cmd(0x00);

send_data_cmd(0x08);

send_ctrl_cmd(0xC0);

send_data_cmd(0x0F);

send_data_cmd(0x0F);

send_ctrl_cmd(0xc1);

send_data_cmd(0x42);

send_ctrl_cmd(0xC2);

send_data_cmd(0x22);

send_ctrl_cmd(0xc5);

send_data_cmd(0x00);

send_data_cmd(0x08);

send_data_cmd(0x80);

send_ctrl_cmd(0xb1);

send_data_cmd(0xB0);

send_data_cmd(0x11);

send_ctrl_cmd(0xb4);

send_data_cmd(0x02);

send_ctrl_cmd(0xb6);

send_data_cmd(0x02);

send_data_cmd(0x02); //cpu?02

send_ctrl_cmd(0xb7);

send_data_cmd(0xC6);

send_ctrl_cmd(0x3a);

send_data_cmd(0x66/*0x55*/);//16bit
?55 18bit ?66

send_ctrl_cmd(0x35);

send_data_cmd(0x00);

send_ctrl_cmd(0x44);

send_data_cmd(0x00);

send_data_cmd(0x5f);

send_ctrl_cmd(0x36);

send_data_cmd(0x08); // 0xc8

send_ctrl_cmd(0x2a);

send_data_cmd(0x00);

send_data_cmd(0x00);

send_data_cmd(0x01);

send_data_cmd(0x3f);

send_ctrl_cmd(0x2b);

send_data_cmd(0x00);

send_data_cmd(0x00);

send_data_cmd(0x01);

send_data_cmd(0xdf);

send_ctrl_cmd(0xe0);

send_data_cmd(0x00);

send_data_cmd(0x1D);

send_data_cmd(0x19);

send_data_cmd(0x0c);

send_data_cmd(0x0f);

send_data_cmd(0x0A);

send_data_cmd(0x45);

send_data_cmd(0x95);

send_data_cmd(0x38);

send_data_cmd(0x0a);

send_data_cmd(0x12);

send_data_cmd(0x03);

send_data_cmd(0x09);

send_data_cmd(0x06);

send_data_cmd(0x00);

send_ctrl_cmd(0xe1);

send_data_cmd(0x0f);

send_data_cmd(0x37);

send_data_cmd(0x35);

send_data_cmd(0x0C);

send_data_cmd(0x0d);

send_data_cmd(0x04);

send_data_cmd(0x48);

send_data_cmd(0x43);

send_data_cmd(0x35);

send_data_cmd(0x04);

send_data_cmd(0x0D);

send_data_cmd(0x02);

send_data_cmd(0x1C);

send_data_cmd(0x18);

send_data_cmd(0x0F);

send_ctrl_cmd(0x11);

MDELAY(120);

send_ctrl_cmd(0x29);

send_ctrl_cmd(0x2c);

MDELAY(10);

}

// ---------------------------------------------------------------------------

// LCM Driver Implementations

// ---------------------------------------------------------------------------

static void lcm_set_util_funcs(const LCM_UTIL_FUNCS
*util)

{

memcpy(&lcm_util, util, sizeof(LCM_UTIL_FUNCS));

}

static void lcm_get_params(LCM_PARAMS
*params)

{

memset(params, 0, sizeof(LCM_PARAMS));

params->type = LCM_TYPE_DBI;

params->ctrl = LCM_CTRL_PARALLEL_DBI;

params->width = FRAME_WIDTH;

params->height = FRAME_HEIGHT;

params->io_select_mode = 1;

params->dbi.port = 0; // 1;

//params->dbi.clock_freq = LCM_DBI_CLOCK_FREQ_104M;
//aa

params->dbi.data_width = LCM_DBI_DATA_WIDTH_18BITS;//LCM_DBI_DATA_WIDTH_16BITS;

params->dbi.data_format.color_order = LCM_COLOR_ORDER_RGB;

params->dbi.data_format.trans_seq = LCM_DBI_TRANS_SEQ_MSB_FIRST;

params->dbi.data_format.padding = LCM_DBI_PADDING_ON_LSB; //LCM_DBI_PADDING_ON_LSB;
//bb

params->dbi.data_format.format = LCM_DBI_FORMAT_RGB666; //LCM_DBI_FORMAT_RGB565;

params->dbi.data_format.width = LCM_DBI_DATA_WIDTH_18BITS; //LCM_DBI_DATA_WIDTH_16BITS;

params->dbi.cpu_write_bits = LCM_DBI_CPU_WRITE_32_BITS; //LCM_DBI_CPU_WRITE_16_BITS;

params->dbi.io_driving_current = LCM_DRIVING_CURRENT_6575_8MA ; //
0;

/* params->dbi.parallel.write_setup = 1;

params->dbi.parallel.write_hold = 1;

params->dbi.parallel.write_wait = 9; // 3;

params->dbi.parallel.read_setup = 1;

params->dbi.parallel.read_latency = 31;

params->dbi.parallel.wait_period = 2;*/

params->dbi.parallel.write_setup = 2;

params->dbi.parallel.write_hold = 2;

params->dbi.parallel.write_wait = 15;

params->dbi.parallel.read_setup = 1;

params->dbi.parallel.read_latency = 31;

params->dbi.parallel.wait_period = 2;

params->dbi.parallel.cs_high_width = 0;

// enable tearing-free

// params->dbi.te_mode = LCM_DBI_TE_MODE_VSYNC_ONLY;

// params->dbi.te_edge_polarity = LCM_POLARITY_FALLING;

/* params->dbi.te_mode = LCM_DBI_TE_MODE_VSYNC_OR_HSYNC;

params->dbi.te_edge_polarity = LCM_POLARITY_RISING;

params->dbi.te_hs_delay_cnt = 50;

params->dbi.te_vs_width_cnt = 277;

params->dbi.te_vs_width_cnt_div = LCM_DBI_TE_VS_WIDTH_CNT_DIV_16;*/

}

#define GPIO_LCD_RST 18 //GPIO18

#define GPIO_MODE_00 0

#define GPIO_DIR_OUT 1

#define GPIO_OUT_ONE 1

#define GPIO_OUT_ZERO 0

extern s32
mt_set_gpio_mode(u32 u4Pin, u32 u4Mode);

extern s32
mt_set_gpio_out(u32 u4Pin, u32 u4PinOut);

extern s32
mt_set_gpio_dir(u32 u4Pin, u32 u4Dir);

static void lcm_init(void)

{

/* SET_RESET_PIN(0);

MDELAY(200);

SET_RESET_PIN(1);

MDELAY(400);*/

// SET_RESET_PIN(1);

mt_set_gpio_mode(GPIO_LCD_RST,GPIO_MODE_00);

mt_set_gpio_dir(GPIO_LCD_RST,GPIO_DIR_OUT);

mt_set_gpio_out(GPIO_LCD_RST,GPIO_OUT_ONE);

MDELAY(1);

//SET_RESET_PIN(0);

mt_set_gpio_out(GPIO_LCD_RST,GPIO_OUT_ZERO);

MDELAY(10);

//SET_RESET_PIN(1);

mt_set_gpio_out(GPIO_LCD_RST,GPIO_OUT_ONE);

MDELAY(100);

init_lcm_registers();

}

static void lcm_suspend(void)

{

send_ctrl_cmd(0x28);

MDELAY(20);

send_ctrl_cmd(0x10);

MDELAY(100);

}

static void lcm_resume(void)

{

send_ctrl_cmd(0x11);

MDELAY(100);

send_ctrl_cmd(0x29);

//MDELAY(100);

/*

send_ctrl_cmd(0x29);

MDELAY(120);

send_ctrl_cmd(0x11);

MDELAY(120); */

}

static void lcm_update(unsigned int x,
unsigned int y,

unsigned int width,
unsigned int height)

{

unsigned int x0
= x;

unsigned int y0
= y;

unsigned int x1
= x0 + width - 1;

unsigned int y1
= y0 + height - 1;

print( "[LCM] *********************ili9486 lcm_update*******************\n\r");

send_ctrl_cmd(0x2A);

send_data_cmd(HIGH_BYTE(x0));

send_data_cmd(LOW_BYTE(x0));

send_data_cmd(HIGH_BYTE(x1));

send_data_cmd(LOW_BYTE(x1));

send_ctrl_cmd(0x2B);

send_data_cmd(HIGH_BYTE(y0));

send_data_cmd(LOW_BYTE(y0));

send_data_cmd(HIGH_BYTE(y1));

send_data_cmd(LOW_BYTE(y1));

// Write To GRAM

send_ctrl_cmd(0x2C);

}

static unsigned int lcm_compare_id(void)

{

return 1;

}

// ---------------------------------------------------------------------------

// Get LCM Driver Hooks

// ---------------------------------------------------------------------------

LCM_DRIVER ili9486_lcm_drv =

{

.name = "ili9486",

.set_util_funcs = lcm_set_util_funcs,

.get_params = lcm_get_params,

.init = lcm_init,

.suspend = lcm_suspend,

.resume = lcm_resume,

.update = lcm_update,

.compare_id = lcm_compare_id

};

注意事项：

1.调试屏幕主要的工作是初始化和时序设置

2.编译的时候，仅仅使用./mk r ub k 是不够的，还需要运行./mk bootimage命令

3.可能是更改了gpio口中LRSTB的原因导致reset失败，代码中通过以下代码手动设置reset信号

[cpp] view
plaincopy

static void lcm_init(void)

{

// SET_RESET_PIN(1);

mt_set_gpio_mode(GPIO_LCD_RST,GPIO_MODE_00);

mt_set_gpio_dir(GPIO_LCD_RST,GPIO_DIR_OUT);

mt_set_gpio_out(GPIO_LCD_RST,GPIO_OUT_ONE);

MDELAY(1);

//SET_RESET_PIN(0);

mt_set_gpio_out(GPIO_LCD_RST,GPIO_OUT_ZERO);

MDELAY(10);

//SET_RESET_PIN(1);

mt_set_gpio_out(GPIO_LCD_RST,GPIO_OUT_ONE);

MDELAY(100);

...

}