Exchange 2010 Postmaster 发送垃圾邮件解决方法、NDR攻击、大量垃圾邮件
2014-06-26 16:32
197 查看
拓扑图:
在这里,先配置1和3[1.在R1配置重发布直连路由,标记10并且路数为10; 3.在R3配置重发布直连路由,跳数设置为4;],以供后面好测试:
配置参数:
R1:
router ospf 1
redistribute connected metric 10 subnets
tag 10
network 192.168.12.0 0.0.0.255 area 0
network 192.168.100.0 0.0.0.255 area 0
R3:
router rip
version 2
redistribute connected metric 4
network 192.168.200.0
network 200.168.23.0
no
auto-summary
查看配置效果:
R2:
r2#SH IP ROU
C
192.168.12.0/24 is directly connected, Ethernet0/0
C
200.168.23.0/24 is directly connected, Ethernet0/1
O E2
192.168.110.0/24 [110/10] via 192.168.12.1, 00:12:30, Ethernet0/0
R
192.168.200.0/24 [120/1] via 200.168.23.2, 00:00:01, Ethernet0/1
10.0.0.0/24 is subnetted, 1 subnets
R 10.1.1.0 [120/4] via 200.168.23.2,
00:00:01, Ethernet0/1
192.168.100.0/32 is subnetted, 1 subnets
O
192.168.100.1 [110/11] via 192.168.12.1, 00:12:30, Ethernet0/0
r2#
可以看出R2学习到R1重发布的直连路由192.168.110.0/24的跳数为10;学习到R3重发布的直连路由10.1.1.0/24的跳数为4.
接下来配置2[2.RIP路由协议重发布OSPF路由,要求只重分标记为10的OSPF路由,初始量度值为10;]:
配置参数:
R1:
route-map ospf permit 10
match tag 10
set
metric 10
router rip
version 2
redistribute ospf 1 route-map ospf
network 200.168.23.0
no
auto-summary
查看配置效果:
R3:
r3#sh ip rou
C
200.168.23.0/24 is directly connected, Ethernet0/1
R 192.168.110.0/24 [120/10] via 200.168.23.1,
00:00:15, Ethernet0/1
C
192.168.200.0/24 is directly connected, Loopback1
10.0.0.0/24 is subnetted, 1 subnets
C
10.1.1.0 is directly connected, Loopback2
r3#
可以看到R3学习到了OSPF网络中标记为10的路由192.168.110.0/24,R2将它重发布到RIP跳数为10.
接下来配置4[4.OSPF路由协议重发布RIP路由,要求只重分布路数为4的路由并且路由网络地址在10.0.0.0/8范围内的RIP路由,在OSPF路由域中,设该路由类型为外部路由type-1,初始量度值为40,路由标记值为40.]
配置参数:
R2:
access-list 10 permit 10.0.0.0 0.255.255.255
route-map rip permit 10
match ip address
10
match metric 4
set metric 40
set metric-type
type-1
set tag 40
router ospf 1
redistribute rip subnets route-map rip
network
192.168.12.0 0.0.0.255 area 0
查看配置:
R1:
C
192.168.12.0/24 is directly connected, Ethernet0/0
C 192.168.110.0/24
is directly connected, Loopback2
10.0.0.0/24 is
subnetted, 1 subnets
O E1 10.1.1.0 [110/50] via 192.168.12.2,
00:01:45, Ethernet0/0
C
192.168.100.0/24 is directly connected, Loopback1
r1#
可以看到R1学习到了R3重发布的标记为4的10.1.1.0/24的路由,是R2将它重发布进OSPF,配置为type-1类型,度量值为40,标记为40的路由!!!
配置成功!!!本文出自 “Yolo” 博客,请务必保留此出处http://4708948.blog.51cto.com/4698948/1130956
在这里,先配置1和3[1.在R1配置重发布直连路由,标记10并且路数为10; 3.在R3配置重发布直连路由,跳数设置为4;],以供后面好测试:
配置参数:
R1:
router ospf 1
redistribute connected metric 10 subnets
tag 10
network 192.168.12.0 0.0.0.255 area 0
network 192.168.100.0 0.0.0.255 area 0
R3:
router rip
version 2
redistribute connected metric 4
network 192.168.200.0
network 200.168.23.0
no
auto-summary
查看配置效果:
R2:
r2#SH IP ROU
C
192.168.12.0/24 is directly connected, Ethernet0/0
C
200.168.23.0/24 is directly connected, Ethernet0/1
O E2
192.168.110.0/24 [110/10] via 192.168.12.1, 00:12:30, Ethernet0/0
R
192.168.200.0/24 [120/1] via 200.168.23.2, 00:00:01, Ethernet0/1
10.0.0.0/24 is subnetted, 1 subnets
R 10.1.1.0 [120/4] via 200.168.23.2,
00:00:01, Ethernet0/1
192.168.100.0/32 is subnetted, 1 subnets
O
192.168.100.1 [110/11] via 192.168.12.1, 00:12:30, Ethernet0/0
r2#
可以看出R2学习到R1重发布的直连路由192.168.110.0/24的跳数为10;学习到R3重发布的直连路由10.1.1.0/24的跳数为4.
接下来配置2[2.RIP路由协议重发布OSPF路由,要求只重分标记为10的OSPF路由,初始量度值为10;]:
配置参数:
R1:
route-map ospf permit 10
match tag 10
set
metric 10
router rip
version 2
redistribute ospf 1 route-map ospf
network 200.168.23.0
no
auto-summary
查看配置效果:
R3:
r3#sh ip rou
C
200.168.23.0/24 is directly connected, Ethernet0/1
R 192.168.110.0/24 [120/10] via 200.168.23.1,
00:00:15, Ethernet0/1
C
192.168.200.0/24 is directly connected, Loopback1
10.0.0.0/24 is subnetted, 1 subnets
C
10.1.1.0 is directly connected, Loopback2
r3#
可以看到R3学习到了OSPF网络中标记为10的路由192.168.110.0/24,R2将它重发布到RIP跳数为10.
接下来配置4[4.OSPF路由协议重发布RIP路由,要求只重分布路数为4的路由并且路由网络地址在10.0.0.0/8范围内的RIP路由,在OSPF路由域中,设该路由类型为外部路由type-1,初始量度值为40,路由标记值为40.]
配置参数:
R2:
access-list 10 permit 10.0.0.0 0.255.255.255
route-map rip permit 10
match ip address
10
match metric 4
set metric 40
set metric-type
type-1
set tag 40
router ospf 1
redistribute rip subnets route-map rip
network
192.168.12.0 0.0.0.255 area 0
查看配置:
R1:
C
192.168.12.0/24 is directly connected, Ethernet0/0
C 192.168.110.0/24
is directly connected, Loopback2
10.0.0.0/24 is
subnetted, 1 subnets
O E1 10.1.1.0 [110/50] via 192.168.12.2,
00:01:45, Ethernet0/0
C
192.168.100.0/24 is directly connected, Loopback1
r1#
可以看到R1学习到了R3重发布的标记为4的10.1.1.0/24的路由,是R2将它重发布进OSPF,配置为type-1类型,度量值为40,标记为40的路由!!!
配置成功!!!本文出自 “Yolo” 博客,请务必保留此出处http://4708948.blog.51cto.com/4698948/1130956
相关文章推荐
- 关于exchange 2010 管理代理发送\代表发送权限设置无法生效的解决方法
- Exchange 2003服务器被中继大量发送垃圾邮件解决过程?
- Exchange 2003队列中堆积大量垃圾邮件解决方法?
- Exchange 2003服务器被中继大量发送垃圾邮件解决过程?
- Exchange 2003队列中堆积大量垃圾邮件解决方法?
- 多种方法解决Exchange 2010 EMC批量启用邮箱之后出现乱码问题
- STMP发送邮件被当垃圾邮件处理的解决方法
- Exchange 2010无法安装问题解决方法 推荐
- 关于exchange 2010账户迁移至其他exchange 2010服务器一致卡在95%或99%的解决方法
- 多种方法解决Exchange 2010 EMC批量启用邮箱之后出..
- 【Vegas原创】exchange发送附件,收到的是txt文件或是被过滤的解决方法
- 多种方法解决Exchange 2010 EMC批量启用邮箱之后出现乱码问题 推荐
- Exchange 2010无法安装问题解决方法
- Exchange 2010 添加DAG成员报静态地址配置错误问题解决方法
- Exchange 2010一例发信失败解决方法
- Exchange 2010 防止匿名用户发送垃圾邮件
- Exchange 2010 删除的邮箱不会立即显示 和 还原报错解决方法
- 【Vegas原创】exchange发送附件,收到的是txt文件或是被过滤的解决方法
- Exchange 2010的一例发信失败解决方法