运放中不使用引脚正确处理方式
2014-04-11 13:34
2226 查看
一块集成运算放大器通常包括多个分离的运放单元,一般我们不能全部用到,那么这些不使用的运放单元怎么处理?图1示意了一种元件最少的正确处理方式,图2是一些常见的错误方式,这些方式因为浮空输入或者地平面浮动等等可能会引起振荡。
![](http://img233.ph.126.net/r4vasIkKofOYUuffohEqQw==/1747115180444466971.jpg)
图1 不使用运放单元的正确处理方式
![](http://img.ph.126.net/MS2Gn91rrpMPPejMUSiipA==/3320560300257120548.jpg)
图2 不使用运放单元的错误处理方式 以下是对于错误处理方式的原文解释 A. This is the worst thing to do with an uncommitted op amp. Both inputs are floating and willpick up noise and the output may switch from rail to rail unpredictably. This configuration willdraw varying amounts of supply current and will couple noise into the other op amps and mayadd noise to the power and ground traces.
B. These two circuits are not recommended because they are stressful to the op amp inputs.This circuit applies the maximum potential across the input and can damage certain op ampssuch as those with diode clamps between the inputs. The op amp output will be in a knownstate and will be railed low in the first circuit and railed high in the second. Railing an op amp's output low causes the op amp to consume more supply current.
C. These two circuits are bad because the output will be railed in an unknown state. The outputstate will be determined by the value of the input stage's offset voltage. Due to the randomness of input offset voltage it cannot be predetermined if the output will be railed high or low. Inaddition to the output's unknown state there is a likely chance the output will change states over
www.maxim-ic.com/an1957 Page 4 of 5 temperature inducing unnecessary noise in the circuit. Railing an op amp's output low causes the op amp to consume more supply current.
D. These two circuits are the most common mistake made when terminating an uncommittedop amp. They are equally bad because the op amp's output will be railed low, causing the opamp to consume more supply current. Avoiding The Uncommitted Amplifier Yields Many Benefits In many cases it is beneficial to avoid having an uncommitted amplifier. The next-generation of sub-micron technology op amps are affordable and are available in tiny packages. Instead of using three of four op amps in a TSSOP package consider using only what you need. Using multiple single op amps in small SC70 packages or a combination of a dual op amp in a tiny SOT23 package and a single op amp offers the following benefits:
· Avoids the issue of the uncommitted amplifier
· Reduces power dissipation by eliminated extra amplifiers
· Reduces PCB area by using smaller components (Figure 4)
· Eases PCB layout and reduces traces length
· Less expensive
![](http://img233.ph.126.net/r4vasIkKofOYUuffohEqQw==/1747115180444466971.jpg)
图1 不使用运放单元的正确处理方式
![](http://img.ph.126.net/MS2Gn91rrpMPPejMUSiipA==/3320560300257120548.jpg)
图2 不使用运放单元的错误处理方式 以下是对于错误处理方式的原文解释 A. This is the worst thing to do with an uncommitted op amp. Both inputs are floating and willpick up noise and the output may switch from rail to rail unpredictably. This configuration willdraw varying amounts of supply current and will couple noise into the other op amps and mayadd noise to the power and ground traces.
B. These two circuits are not recommended because they are stressful to the op amp inputs.This circuit applies the maximum potential across the input and can damage certain op ampssuch as those with diode clamps between the inputs. The op amp output will be in a knownstate and will be railed low in the first circuit and railed high in the second. Railing an op amp's output low causes the op amp to consume more supply current.
C. These two circuits are bad because the output will be railed in an unknown state. The outputstate will be determined by the value of the input stage's offset voltage. Due to the randomness of input offset voltage it cannot be predetermined if the output will be railed high or low. Inaddition to the output's unknown state there is a likely chance the output will change states over
www.maxim-ic.com/an1957 Page 4 of 5 temperature inducing unnecessary noise in the circuit. Railing an op amp's output low causes the op amp to consume more supply current.
D. These two circuits are the most common mistake made when terminating an uncommittedop amp. They are equally bad because the op amp's output will be railed low, causing the opamp to consume more supply current. Avoiding The Uncommitted Amplifier Yields Many Benefits In many cases it is beneficial to avoid having an uncommitted amplifier. The next-generation of sub-micron technology op amps are affordable and are available in tiny packages. Instead of using three of four op amps in a TSSOP package consider using only what you need. Using multiple single op amps in small SC70 packages or a combination of a dual op amp in a tiny SOT23 package and a single op amp offers the following benefits:
· Avoids the issue of the uncommitted amplifier
· Reduces power dissipation by eliminated extra amplifiers
· Reduces PCB area by using smaller components (Figure 4)
· Eases PCB layout and reduces traces length
· Less expensive
相关文章推荐
- 运放中不使用引脚正确处理方式
- PCB中运放不使用管脚的正确处理方式
- STM32未使用引脚的处理方式及推荐硬件设计规范
- 小样本大概率事件的正确处理方式 - 3. 实际使用
- 电脑出现IE已经阻止此站点以不安全的方式使用ActiveX控件,因此该网页无法正确显示”的处理办法
- Javascript中parseInt的正确使用方式
- java使用HttpURLConnection检索网站时403错误处理方式
- glDrawArrays 函数使用的正确方式是什么?
- 正确使用MySQL JDBC setFetchSize()方法解决JDBC处理大结果集 java.lang.OutOfMemoryError: Java heap space
- 批处理之 正确使用for语句 以及!errorlevel!、%errorlevel% 与 DelayedExpansion用法详解
- Java的图形处理中经常使用坐标方式
- 使用 ajax 方式提交表单,并获取后台处理结果
- ListCtrl中使用SendMessage的方式来处理多选
- Android中的内存管理机制以及正确的使用方式
- 使用 Anthem.NET 的常见回调(Callback)处理方式小结
- Android 使用Eclipse工具正确修改项目包名的方式
- 中文分词语言处理HanPL配置,以及在eclipse中安装使用方式
- 联合体的正确使用方式
- JavaBean中使用JDBC方式进行事务处理
- 如何正确使用Java异常处理机制