Kernel panic - not syncing: Attempted to kill init!(移植linux2.6.29.4进友善mini2440开发板时遇到)

移植linux2.6.29.4进友善mini2440开发板	发布时间：2009-07-08 23:48:48
技术类别：ARM

终于移植成功，总结下：

移植linux2.6.29.4内核+yaffs2文件系统过程

软件平台:vm(fodera 9)+arm-linux-gcc 4.3.2

参考资料:网上n多资料

1.修改顶层Makefile文件

直接将Makefile文件里面的 ln193

ARCH ?= $(SUBARCH)

CROSS_COMPILE ?=

改为:

ARCH ?= arm

CROSS_COMPILE ?=arm-linux-

然后用S3C2410的默认配置文件

#make s3c2410_defconfig //此命令 configuration written to .config

//要先按上面方法修改完成Makefile文件才能执行这一步

2.修改时钟,不修改超级终端中会出现乱码

修改Arch/arm/mach-s3c2440/mach-smdk2440.c ln163

S3c24xx_init_clocks(16934400);

改为:

S3c24xx_init_clocks(12000000);

3.修改对nand的分区信息。要让内核知道nand flash的分区信息，设置成跟bootloader一致。

在arch/arm/plat-s3c24xx/common-smdk.c中修改smdk_default_nand_part[]

/* NAND parititon from 2.4.18-swl5 */

static struct mtd_partition friendly_arm_default_nand_part[] = {

[0] = {

.name = "supervivi",

.size = 0x00030000,

.offset = 0,

},

[1] = {

.name = "Kernel",

.offset = 0x00050000,

.size = 0x00200000,

},

[2] = {

.name = "root",

.offset = 0x00250000,

.size = 0x03dac000,

}

};

4.修改CPUID，不修改将会出现无法进入内核由于CPU mach_type 不对应找不到对应的CPU。

arch/arm/tools/mach-types 这个文件打开修改对应CPU 的ID

修改 S3C2440 对应为 782。

5.修改drivers/mtd/nand/s3c2410.c

NAND_ECC_SOFT；----》NAND_ECC_NONE;

没试不修改行不行。

6.移植YAFFS2

将原来官方内核中/fs/Kconfig

/fs/Makefile

和yaffs2文件夹拷贝到相应的位置

7．Make menuconfig

修改Kernel Features --->

[*] Use the ARM EABI to compile the kernel

[*] Allow old ABI binaries to run with this kernel (EXPERIMENTA)

把这个选上。

如果不选启动时会出现Kernel panic - not syncing: Attempted to kill init!

8.make zImage

在/linux2.6.29.2/arch/arm/boot就可以找到zImage文件了

总结下：

主要改的文件有：

arch/arm/mach-s3c2440/mach-smdk2440.c（时钟）

arch/arm/plat-s3c24xx/common-smdk2440.c（nandflash）

arch/arm/tools/mach-types (CPU的ID)

移植YAFFS2

下载进友善的mini2440开发板：

Console: colour dummy device 80x30

console [ttySAC0] enabled

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 64MB = 64MB total

Memory: 61024KB available (3360K code, 323K data, 144K init)

Calibrating delay loop... 201.93 BogoMIPS (lpj=504832)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

net_namespace: 716 bytes

NET: Registered protocol family 16

S3C2410 Power Management, (c) 2004 Simtec Electronics

S3C2440: Initialising architecture

S3C2440: IRQ Support

S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics

DMA channel 0 at c4808000, irq 33

DMA channel 1 at c4808040, irq 34

DMA channel 2 at c4808080, irq 35

DMA channel 3 at c48080c0, irq 36

S3C244X: Clock Support, DVS off

bio: create slab <bio-0> at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

NET: Registered protocol family 1

NetWinder Floating Point Emulator V0.97 (extended precision)

JFFS2 version 2.2. (NAND) (SUMMARY) 漏 2001-2006 Red Hat, Inc.

yaffs Jul 8 2009 22:30:08 Installing.

msgmni has been set to 119

io scheduler noop registered

io scheduler anticipatory registered (default)

io scheduler deadline registered

io scheduler cfq registered

Console: switching to colour frame buffer device 30x40

fb0: s3c2410fb frame buffer device

lp: driver loaded but no devices found

ppdev: user-space parallel port driver

Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled

s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440

s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440

s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440

brd: module loaded

loop: module loaded

dm9000 Ethernet Driver, V1.31

Uniform Multi-Platform E-IDE driver

ide-gd driver 1.18

ide-cd driver 5.00

Driver 'sd' needs updating - please use bus_type methods

S3C24XX NAND Driver, (c) 2004 Simtec Electronics

s3c2440-nand s3c2440-nand: Tacls="3", 29ns Twrph0=7 69ns, Twrph1=3 29ns

NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit

)

NAND_ECC_NONE selected by board driver. This is not recommended !!

Scanning device for bad blocks

Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":

0x000000000000-0x000000030000 : "supervivi"

0x000000050000-0x000000250000 : "Kernel"

0x000000250000-0x000003ffc000 : "root"

usbmon: debugfs is not available

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

s3c2410-ohci s3c2410-ohci: S3C24XX OHCI

s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1

s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

usbcore: registered new interface driver libusual

usbcore: registered new interface driver usbserial

USB Serial support registered for generic

usbcore: registered new interface driver usbserial_generic

usbserial: USB Serial Driver core

USB Serial support registered for FTDI USB Serial Device

usbcore: registered new interface driver ftdi_sio

ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver

USB Serial support registered for pl2303

usbcore: registered new interface driver pl2303

pl2303: Prolific PL2303 USB to serial adaptor driver

mice: PS/2 mouse device common for all mice

S3C24XX RTC, (c) 2004,2006 Simtec Electronics

s3c2440-i2c s3c2440-i2c: slave address 0x10

s3c2440-i2c s3c2440-i2c: bus frequency set to 98 KHz

s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter

S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics

s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled

TCP cubic registered

NET: Registered protocol family 17

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

drivers/rtc/hctosys.c: unable to open rtc device (rtc0)

yaffs: dev is 32505858 name is "mtdblock2"

yaffs: passed flags ""

yaffs: Attempting MTD mount on 31.2, "mtdblock2"

yaffs_read_super: isCheckpointed 0

VFS: Mounted root (yaffs filesystem) on device 31:2.

Freeing init memory: 144K

hwclock: can't open '/dev/misc/rtc': No such file or directory

[01/Jan/1970:00:00:14 +0000] boa: server version Boa/0.94.13

[01/Jan/1970:00:00:14 +0000] boa: server built Mar 26 2009 at 15:28:42.

[01/Jan/1970:00:00:14 +0000] boa: starting server pid="913", port 80

open device leds: No such file or directory

Try to bring eth0 interface up......ifconfig: SIOCGIFFLAGS: No such device

ifconfig: SIOCSIFHWADDR: No such device

ifconfig: SIOCSIFADDR: No such device

route: SIOCADDRT: Network is unreachable

Done

Please press Enter to activate this console.

[root@FriendlyARM /]#

[root@FriendlyARM /]#

[root@FriendlyARM /]#

[root@FriendlyARM /]#

[root@FriendlyARM /]#

[root@FriendlyARM /]# ls

bin home lost+found root tmp www

dev lib opt sbin usr

etc linuxrc proc sys var

[root@FriendlyARM /]# ls

bin home lost+found root tmp www

dev lib opt sbin usr

etc linuxrc proc sys var

[root@FriendlyARM /]# cd dev

[root@FriendlyARM /dev]# ls

console ptyvd ttyd9

cpu_dma_latency ptyve ttyda

fb0 ptyvf ttydb

full ptyw0 ttydc

input ptyw1 ttydd

kmem ptyw2 ttyde

kmsg ptyw3 ttydf

log ptyw4 ttye0

loop ptyw5 ttye1

mem ptyw6 ttye2

mtd0 ptyw7 ttye3

mtd0ro ptyw8 ttye4

mtd1 ptyw9 ttye5

mtd1ro ptywa ttye6

mtd2 ptywb ttye7

mtd2ro ptywc ttye8

mtdblock0 ptywd ttye9

mtdblock1 ptywe ttyea

mtdblock2 ptywf ttyeb

network_latency ptyx0 ttyec

network_throughput ptyx1 ttyed

null ptyx2 ttyee

port ptyx3 ttyef

psaux ptyx4 ttyp0

ptmx ptyx5 ttyp1

pts ptyx6 ttyp2

ptya0 ptyx7 ttyp3

ptya1 ptyx8 ttyp4

ptya2 ptyx9 ttyp5

ptya3 ptyxa ttyp6

ptya4 ptyxb ttyp7

ptya5 ptyxc ttyp8

ptya6 ptyxd ttyp9

ptya7 ptyxe ttypa

ptya8 ptyxf ttypb

ptya9 ptyy0 ttypc

ptyaa ptyy1 ttypd

ptyab ptyy2 ttype

ptyac ptyy3 ttypf

ptyad ptyy4 ttyq0

ptyae ptyy5 ttyq1

ptyaf ptyy6 ttyq2

ptyb0 ptyy7 ttyq3

ptyb1 ptyy8 ttyq4

ptyb2 ptyy9 ttyq5

ptyb3 ptyya ttyq6

ptyb4 ptyyb ttyq7

ptyb5 ptyyc ttyq8

ptyb6 ptyyd ttyq9

ptyb7 ptyye ttyqa

ptyb8 ptyyf ttyqb

ptyb9 ptyz0 ttyqc

ptyba ptyz1 ttyqd

ptybb ptyz2 ttyqe

ptybc ptyz3 ttyqf

ptybd ptyz4 ttyr0

ptybe ptyz5 ttyr1

ptybf ptyz6 ttyr2

ptyc0 ptyz7 ttyr3

ptyc1 ptyz8 ttyr4

ptyc2 ptyz9 ttyr5

ptyc3 ptyza ttyr6

ptyc4 ptyzb ttyr7

ptyc5 ptyzc ttyr8

ptyc6 ptyzd ttyr9

ptyc7 ptyze ttyra

ptyc8 ptyzf ttyrb

ptyc9 ram0 ttyrc

ptyca ram1 ttyrd

ptycb ram10 ttyre

ptycc ram11 ttyrf

ptycd ram12 ttys0

ptyce ram13 ttys1

ptycf ram14 ttys2

ptyd0 ram15 ttys3

ptyd1 ram2 ttys4

ptyd2 ram3 ttys5

ptyd3 ram4 ttys6

ptyd4 ram5 ttys7

ptyd5 ram6 ttys8

ptyd6 ram7 ttys9

ptyd7 ram8 ttysa

ptyd8 ram9 ttysb

ptyd9 random ttysc

ptyda root ttysd

ptydb shm ttyse

ptydc tty ttysf

ptydd tty0 ttyt0

ptyde tty1 ttyt1

ptydf tty10 ttyt2

ptye0 tty11 ttyt3

ptye1 tty12 ttyt4

ptye2 tty13 ttyt5

ptye3 tty14 ttyt6

ptye4 tty15 ttyt7

ptye5 tty16 ttyt8

ptye6 tty17 ttyt9

ptye7 tty18 ttyta

ptye8 tty19 ttytb

ptye9 tty2 ttytc

ptyea tty20 ttytd

ptyeb tty21 ttyte

ptyec tty22 ttytf

ptyed tty23 ttyu0

ptyee tty24 ttyu1

ptyef tty25 ttyu2

ptyp0 tty26 ttyu3

ptyp1 tty27 ttyu4

ptyp2 tty28 ttyu5

ptyp3 tty29 ttyu6

ptyp4 tty3 ttyu7

ptyp5 tty30 ttyu8

ptyp6 tty31 ttyu9

ptyp7 tty32 ttyua

ptyp8 tty33 ttyub

ptyp9 tty34 ttyuc

ptypa tty35 ttyud

ptypb tty36 ttyue

ptypc tty37 ttyuf

ptypd tty38 ttyv0

ptype tty39 ttyv1

ptypf tty4 ttyv2

ptyq0 tty40 ttyv3

ptyq1 tty41 ttyv4

ptyq2 tty42 ttyv5

ptyq3 tty43 ttyv6

ptyq4 tty44 ttyv7

ptyq5 tty45 ttyv8

ptyq6 tty46 ttyv9

ptyq7 tty47 ttyva

ptyq8 tty48 ttyvb

ptyq9 tty49 ttyvc

ptyqa tty5 ttyvd

ptyqb tty50 ttyve

ptyqc tty51 ttyvf

ptyqd tty52 ttyw0

ptyqe tty53 ttyw1

ptyqf tty54 ttyw2

ptyr0 tty55 ttyw3

ptyr1 tty56 ttyw4

ptyr2 tty57 ttyw5

ptyr3 tty58 ttyw6

ptyr4 tty59 ttyw7

ptyr5 tty6 ttyw8

ptyr6 tty60 ttyw9

ptyr7 tty61 ttywa

ptyr8 tty62 ttywb

ptyr9 tty63 ttywc

ptyra tty7 ttywd

ptyrb tty8 ttywe

ptyrc tty9 ttywf

ptyrd ttyS0 ttyx0

ptyre ttyS1 ttyx1

ptyrf ttyS2 ttyx2

ptys0 ttyS3 ttyx3

ptys1 ttySAC0 ttyx4

ptys2 ttySAC1 ttyx5

ptys3 ttySAC2 ttyx6

ptys4 ttya0 ttyx7

ptys5 ttya1 ttyx8

ptys6 ttya2 ttyx9

ptys7 ttya3 ttyxa

ptys8 ttya4 ttyxb

ptys9 ttya5 ttyxc

ptysa ttya6 ttyxd

ptysb ttya7 ttyxe

ptysc ttya8 ttyxf

ptysd ttya9 ttyy0

ptyse ttyaa ttyy1

ptysf ttyab ttyy2

ptyt0 ttyac ttyy3

ptyt1 ttyad ttyy4

ptyt2 ttyae ttyy5

ptyt3 ttyaf ttyy6

ptyt4 ttyb0 ttyy7

ptyt5 ttyb1 ttyy8

ptyt6 ttyb2 ttyy9

ptyt7 ttyb3 ttyya

ptyt8 ttyb4 ttyyb

ptyt9 ttyb5 ttyyc

ptyta ttyb6 ttyyd

ptytb ttyb7 ttyye

ptytc ttyb8 ttyyf

ptytd ttyb9 ttyz0

ptyte ttyba ttyz1

ptytf ttybb ttyz2

ptyu0 ttybc ttyz3

ptyu1 ttybd ttyz4

ptyu2 ttybe ttyz5

ptyu3 ttybf ttyz6

ptyu4 ttyc0 ttyz7

ptyu5 ttyc1 ttyz8

ptyu6 ttyc2 ttyz9

ptyu7 ttyc3 ttyza

ptyu8 ttyc4 ttyzb

ptyu9 ttyc5 ttyzc

ptyua ttyc6 ttyzd

ptyub ttyc7 ttyze

ptyuc ttyc8 ttyzf

ptyud ttyc9 urandom

ptyue ttyca usbdev1.1

ptyuf ttycb usbdev1.1_ep00

ptyv0 ttycc usbdev1.1_ep81

ptyv1 ttycd vcs

ptyv2 ttyce vcs1

ptyv3 ttycf vcs2

ptyv4 ttyd0 vcs3

ptyv5 ttyd1 vcs4

ptyv6 ttyd2 vcsa

ptyv7 ttyd3 vcsa1

ptyv8 ttyd4 vcsa2

ptyv9 ttyd5 vcsa3

ptyva ttyd6 vcsa4

ptyvb ttyd7 watchdog

ptyvc ttyd8 zero

[root@FriendlyARM /dev]# cd ..

[root@FriendlyARM /]# ls

bin home lost+found root tmp www

dev lib opt sbin usr

etc linuxrc proc sys var

[root@FriendlyARM /]# cd opt

[root@FriendlyARM /opt]# ls

Qtopia kde

[root@FriendlyARM /opt]# cd root

-/bin/sh: cd: can't cd to root

[root@FriendlyARM /opt]# cd root

-/bin/sh: cd: can't cd to root

[root@FriendlyARM /opt]# cd /root

[root@FriendlyARM /root]# ls

Documents Settings

[root@FriendlyARM /root]#

?

VIVI version 0.1.4 (root@capcross) (gcc version 2.95.3 20010315 (release)) #0.

1.4 Mon Oct 27 10:18:15 CST 2008

MMU table base address = 0x33DFC000

Succeed memory mapping.

DIVN_UPLL0

MPLLVal [M:7fh,P:2h,S:1h]

CLKDIVN:5h

+---------------------------------------------+

| S3C2440A USB Downloader ver R0.03 2004 Jan |

+---------------------------------------------+

USB: IN_ENDPOINT:1 OUT_ENDPOINT:3

FORMAT: <ADDR(DATA):4>+<SIZE(n+10):4>+<DATA:n>+<CS:2>

NOTE: Power off/on or press the reset button for 1 sec

in order to get a valid USB device address.

NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung K9D1208V0M)

Could not found stored vivi parameters. Use default vivi parameters.

Press Return to start the LINUX/Wince now, any other key for vivi

Copy linux kernel from 0x00050000 to 0x30008000, size = 0x00200000 ... done

zImage magic = 0x016f2818

Setup linux parameters at 0x30000100

linux command line is: "noinitrd root="/dev/mtdblock2" init="/linuxrc" console="ttySA"

C0"

MACH_TYPE = 782

NOW, Booting Linux......

Uncompressing Linux.............................................................

........................................................ done, booting the kerne

l.

Linux version 2.6.29.4 (root@localhost.localdomain) (gcc version 4.3.2 (Sourcery

G++ Lite 2008q3-72) ) #5 Wed Jul 8 22:40:26 CST 2009

CPU: ARM920T [41129200] revision 0 (ARMv4T), cr="c0007177"

CPU: VIVT data cache, VIVT instruction cache

Machine: SMDK2440

ATAG_INITRD is deprecated; please update your bootloader.

Memory policy: ECC disabled, Data cache writeback

CPU S3C2440A (id 0x32440001)

S3C24XX Clocks, (c) 2004 Simtec Electronics

S3C244X: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz

CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on

Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256

Kernel command line: noinitrd root="/dev/mtdblock2" init="/linuxrc" console="ttySAC0"

irq: clearing subpending status 00000002

PID hash table entries: 256 (order: 8, 1024 bytes)

Console: colour dummy device 80x30

console [ttySAC0] enabled

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 64MB = 64MB total

Memory: 61024KB available (3360K code, 323K data, 144K init)

Calibrating delay loop... 201.93 BogoMIPS (lpj=504832)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

net_namespace: 716 bytes

NET: Registered protocol family 16

S3C2410 Power Management, (c) 2004 Simtec Electronics

S3C2440: Initialising architecture

S3C2440: IRQ Support

S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics

DMA channel 0 at c4808000, irq 33

DMA channel 1 at c4808040, irq 34

DMA channel 2 at c4808080, irq 35

DMA channel 3 at c48080c0, irq 36

S3C244X: Clock Support, DVS off

bio: create slab <bio-0> at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

NET: Registered protocol family 1

NetWinder Floating Point Emulator V0.97 (extended precision)

JFFS2 version 2.2. (NAND) (SUMMARY) 漏 2001-2006 Red Hat, Inc.

yaffs Jul 8 2009 22:30:08 Installing.

msgmni has been set to 119

io scheduler noop registered

io scheduler anticipatory registered (default)

io scheduler deadline registered

io scheduler cfq registered

Console: switching to colour frame buffer device 30x40

fb0: s3c2410fb frame buffer device

lp: driver loaded but no devices found

ppdev: user-space parallel port driver

Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled

s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440

s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440

s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440

brd: module loaded

loop: module loaded

dm9000 Ethernet Driver, V1.31

Uniform Multi-Platform E-IDE driver

ide-gd driver 1.18

ide-cd driver 5.00

Driver 'sd' needs updating - please use bus_type methods

S3C24XX NAND Driver, (c) 2004 Simtec Electronics

s3c2440-nand s3c2440-nand: Tacls="3", 29ns Twrph0=7 69ns, Twrph1=3 29ns

NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit

)

NAND_ECC_NONE selected by board driver. This is not recommended !!

Scanning device for bad blocks

Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":

0x000000000000-0x000000030000 : "supervivi"

0x000000050000-0x000000250000 : "Kernel"

0x000000250000-0x000003ffc000 : "root"

usbmon: debugfs is not available

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

s3c2410-ohci s3c2410-ohci: S3C24XX OHCI

s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1

s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

usbcore: registered new interface driver libusual

usbcore: registered new interface driver usbserial

USB Serial support registered for generic

usbcore: registered new interface driver usbserial_generic

usbserial: USB Serial Driver core

USB Serial support registered for FTDI USB Serial Device

usbcore: registered new interface driver ftdi_sio

ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver

USB Serial support registered for pl2303

usbcore: registered new interface driver pl2303

pl2303: Prolific PL2303 USB to serial adaptor driver

mice: PS/2 mouse device common for all mice

S3C24XX RTC, (c) 2004,2006 Simtec Electronics

s3c2440-i2c s3c2440-i2c: slave address 0x10

s3c2440-i2c s3c2440-i2c: bus frequency set to 98 KHz

s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter

S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics

s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled

TCP cubic registered

NET: Registered protocol family 17

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

drivers/rtc/hctosys.c: unable to open rtc device (rtc0)

yaffs: dev is 32505858 name is "mtdblock2"

yaffs: passed flags ""

yaffs: Attempting MTD mount on 31.2, "mtdblock2"

yaffs_read_super: isCheckpointed 0

VFS: Mounted root (yaffs filesystem) on device 31:2.

Freeing init memory: 144K

hwclock: can't open '/dev/misc/rtc': No such file or directory

[01/Jan/1970:00:00:14 +0000] boa: server version Boa/0.94.13

[01/Jan/1970:00:00:14 +0000] boa: server built Mar 26 2009 at 15:28:42.

[01/Jan/1970:00:00:14 +0000] boa: starting server pid="913", port 80

open device leds: No such file or directory

Try to bring eth0 interface up......ifconfig: SIOCGIFFLAGS: No such device

ifconfig: SIOCSIFHWADDR: No such device

ifconfig: SIOCSIFADDR: No such device

route: SIOCADDRT: Network is unreachable

Done

Please press Enter to activate this console.

[root@FriendlyARM /]#

[root@FriendlyARM /]#

标签：

[b]Kernel panic - not syncing: Attempted to kill init!

用arm-linux-gcc 4.00以上的编译器做出都 文件系统老是报这个错 ，

而用rm-linux-gcc 3.xx 版本都都不会，看来一下内核的配置

原来问题在这里

Kernel Features --->

[*] Use the ARM EABI to compile the kernel

[*] Allow old ABI binaries to run with this kernel (EXPERIMENTA)

把这个选上就可以了

[/b]