linux测速软件的使用 iperf

PC端的编译过程： 使用的版本是：iperf-2.0.5.tar.gz

直接：./configure --disable-ipv6

然后make ///<----编译好后的二进制在src文件夹下。

在pc端运行： iperf -s -i 1

arm版本的iperf编译过程： ///<---------------需要终端可以执行

删除configure文件的第6567行： $as_echo "#define malloc rpl_malloc" >>confdefs.h

然后

./configure --disable-ipv6 --host=arm-fsl-linux-gnueabi

然后

make

在板子上运行：iperf -t 20 -i 1 -c 192.168.1.167（这个是PC端的IP）

我的arm板子上的信息：

[root@ARM src]# ./iperf -t 20 -i 1 -c 192.168.11.3

------------------------------------------------------------

Client connecting to 192.168.11.3, TCP port 5001

TCP window size: 20.7 KByte (default)

------------------------------------------------------------

[ 3] local 192.168.11.13 port 38098 connected with 192.168.11.3 port 5001

[ ID] Interval Transfer Bandwidth

[ 3] 0.0- 1.0 sec 768 KBytes 6.29 Mbits/sec

[ 3] 1.0- 2.0 sec 1.12 MBytes 9.44 Mbits/sec

[ 3] 2.0- 3.0 sec 1.00 MBytes 8.39 Mbits/sec

[ 3] 3.0- 4.0 sec 768 KBytes 6.29 Mbits/sec

[ 3] 4.0- 5.0 sec 0.00 Bytes 0.00 bits/sec

[ 3] 5.0- 6.0 sec 1.25 MBytes 10.5 Mbits/sec

[ 3] 6.0- 7.0 sec 640 KBytes 5.24 Mbits/sec

[ 3] 7.0- 8.0 sec 0.00 Bytes 0.00 bits/sec

[ 3] 8.0- 9.0 sec 1.12 MBytes 9.44 Mbits/sec

[ 3] 9.0-10.0 sec 1.12 MBytes 9.44 Mbits/sec

[ 3] 10.0-11.0 sec 640 KBytes 5.24 Mbits/sec

[ 3] 11.0-12.0 sec 512 KBytes 4.19 Mbits/sec

[ 3] 12.0-13.0 sec 1.12 MBytes 9.44 Mbits/sec

[ 3] 13.0-14.0 sec 640 KBytes 5.24 Mbits/sec

[ 3] 14.0-15.0 sec 512 KBytes 4.19 Mbits/sec

Every 1s: /sbin/ifconfig eth0 | grep bytes 2013-12-28 02:50:19

RX bytes:564900 (551.6 KiB) TX bytes:17460743 (16.6 MiB)

^C

[root@ARM src]#

[root@ARM src]#

一下转自：http://blog.chinaunix.net/uid-20648944-id-2943611.html

1. # iptraf -g //这个最直观

2. iperf 　Iperf 是一个网络性能测试工具。Iperf可以测试最大TCP和UDP带宽性能。Iperf具有多种参数和UDP特性，可以根据需要调整。Iperf可以报告带宽，延迟抖动和数据包丢失

TCP:

server(pc): iperf -s -i 1

client(ls1b): iperf -t 20 -i 1 -c 192.168.1.167 (pc-ip)

UDP:

server(pc): iperf -u -s -i 1

client(ls1b): iperf -t 10 -i 1 -u -b 1000M -c 192.168.1.90

3. # ifconfig -a

eth0:Link encap:Ethernet HWaddr 00:1e:64:63:ab:fe

inet addr:192.168.3.103 Bcast:192.168.3.255 Mask:255.255.255.0

inet6 addr: fe80::21e:64ff:fe63:abfe/64 Scope:Link

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:70283 errors:0 dropped:0 overruns:0 frame:0

TX packets:46701 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000

RX bytes:73276012 (73.2 MB) TX bytes:6267375 (6.2 MB)

4. # mii-tool -w -v //更详细的用法 man mii-tool

5. ethtool是用来显示和更改网卡设置的工具 更详细的用法 man ethtool

# ethtool eth0 //显示网络端口设置功能

Settings for eth0:

Supported ports: [ TP MII ]

Supported link modes: 10baseT/Half 10baseT/Full

100baseT/Half 100baseT/Full

Supports auto-negotiation: Yes

Advertised link modes: 10baseT/Half 10baseT/Full

100baseT/Half 100baseT/Full

Advertised pause frame use: No

Advertised auto-negotiation: Yes

Link partner advertised link modes: Not reported

Link partner advertised pause frame use: No

Link partner advertised auto-negotiation: No

Speed: 10Mb/s

Duplex: Half

Port: MII

PHYAD: 0

Transceiver: internal

Auto-negotiation: on

Supports Wake-on: pumbg

Wake-on: g

Current message level: 0x00000033 (51)

Link detected: no

# ethtool -i eth0 //显示跟硬件相关的信息

driver: r8169

version: 2.3LK-NAPI

firmware-version:

bus-info: 0000:05:00.0

6. # watch -n 1 "/sbin/ifconfig eth0 | grep bytes"