路由器ospf动态路由配置
2013-07-18 22:36
246 查看
技术原理:
Ospd开放式最短路径优先协议。是目前网络中应用最广泛的路由协议之一。属于内部网络路由协议。能够适应各种规模的网络环境,是典型的链路状态协议。Ospf路由协议通过向全网扩散本设备的链路状态信息,使网络中每台设备最终同步一个具有全网链路状态的数据库,然后路由器采用spf算法。以自己为根,计算到达网络的最短路径,最终形成全网路由信息。
实验步骤:
1.在本实验中的三层交换机上划分vlan10和vlan20,其中vlan10用于连接主机,vlan20用于连接R1.2.路由器之间通过v35电缆通过串口连接,DCE端连接在R1上,配置其时钟频率64000.3.主机和交换机通过直连线,主机与路由器通过交叉线连接。4.在S3560上配置ospf路由协议。5.在路由器R1、R2上配置ospf路由协议6.将pc1、pc2主机默认网关设置为与直连网络设备接口IP地址7.验证pc1、pc2主机之间可以互相通实验图:
S3650配置:
Switch>en
Switch>enable
Switch#config t
Enter configuration commands, one perline. End with CNTL/Z.
Switch(config)#host s3650
s3650(config)#vlan 10
s3650(config-vlan)#name v10
s3650(config-vlan)#exit
s3650(config)#vlan 20
s3650(config-vlan)#name v20
s3650(config-vlan)#exit
s3650(config)#int fa0/10
s3650(config-if)#switchport access vlan 10
s3650(config-if)#exit
s3650(config)#int fa0/20
s3650(config-if)#switchport access vlan 20
s3650(config-if)#exit
s3650(config)#int vlan 10
%LINK-5-CHANGED: Interface Vlan10, changedstate to up
%LINEPROTO-5-UPDOWN: Line protocol onInterface Vlan10, changed state to up
s3650(config-if)#ip address 192.168.1.1255.255.255.0
s3650(config-if)#no shut
s3650(config-if)#exit
s3650(config)#int vlan 20
s3650(config-if)#
%LINK-5-CHANGED: Interface Vlan20, changedstate to up
s3650(config-if)#ip address 192.168.3.1255.255.255.0
s3650(config-if)#no shut
s3650(config-if)#router ospf 1
s3650(config-router)#network 192.168.1.00.0.0.255 area 0
s3650(config-router)#network 192.168.3.00.0.0.255 area 0
s3650(config-router)#exit
s3650(config)#exit
s3650#
%SYS-5-CONFIG_I: Configured from console byconsole
R1配置:
Router>en
Router#config t
Enter configuration commands, one perline. End with CNTL/Z.
Router(config)#host R1
R1(config)#int fa0/0
R1(config-if)#ip address 192.168.3.2255.255.255.0
R1(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0,changed state to up
%LINEPROTO-5-UPDOWN: Line protocol onInterface FastEthernet0/0, changed state to up
R1(config-if)#exit
R1(config)#int serial2/0
R1(config-if)#clock rate 64000
R1(config-if)#ip address 192.168.4.1255.255.255.0
R1(config-if)#no shut
%LINK-5-CHANGED: Interface Serial2/0,changed state to down
R1(config-if)#exit
R1(config)#router ospf 1
R1(config-router)#network 192.168.3.00.0.0.255 area 0
R1(config-router)#network
01:10:13: %OSPF-5-ADJCHG: Process 1, Nbr192.168.3.1 on FastEthernet0/0 from LOADING to FULL, Loading Done
% Incomplete command.
R1(config-router)#network 192.168.4.00.0.0.255 area 0
R1(config-router)#
R2配置:
Router>en
Router#config t
Enter configuration commands, one perline. End with CNTL/Z.
Router(config)#host R2
R2(config)#int fa0/0
R2(config-if)#ip address 192.168.2.1255.255.255.0
R2(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0,changed state to up
%LINEPROTO-5-UPDOWN: Line protocol onInterface FastEthernet0/0, changed state to up
R2(config-if)#exit
R2(config)#int serial2/0
R2(config-if)#ip address 192.168.4.2255.255.255.0
R2(config-if)#no shut
R2(config-if)#
%LINK-5-CHANGED: Interface Serial2/0,changed state to up
R2(config-if)#exit
R2(config)#
%LINEPROTO-5-UPDOWN: Line protocol onInterface Serial2/0, changed state to up
R2(config)#router ospf 1
R2(config-router)#network 192.168.2.00.0.0.255 area 0
R2(config-router)#network 192.168.4.00.0.0.255 area 0
R2(config-router)#exit
R2(config)#
测试:
从pc2 pingpc1.不通
在s3650上配置:
s3650#config t
Enter configuration commands, one perline. End with CNTL/Z.
s3650(config)#ip routing
s3650(config)#exit
s3650#
此时测试已通
Ospd开放式最短路径优先协议。是目前网络中应用最广泛的路由协议之一。属于内部网络路由协议。能够适应各种规模的网络环境,是典型的链路状态协议。Ospf路由协议通过向全网扩散本设备的链路状态信息,使网络中每台设备最终同步一个具有全网链路状态的数据库,然后路由器采用spf算法。以自己为根,计算到达网络的最短路径,最终形成全网路由信息。
实验步骤:
1.在本实验中的三层交换机上划分vlan10和vlan20,其中vlan10用于连接主机,vlan20用于连接R1.2.路由器之间通过v35电缆通过串口连接,DCE端连接在R1上,配置其时钟频率64000.3.主机和交换机通过直连线,主机与路由器通过交叉线连接。4.在S3560上配置ospf路由协议。5.在路由器R1、R2上配置ospf路由协议6.将pc1、pc2主机默认网关设置为与直连网络设备接口IP地址7.验证pc1、pc2主机之间可以互相通实验图:
S3650配置:
Switch>en
Switch>enable
Switch#config t
Enter configuration commands, one perline. End with CNTL/Z.
Switch(config)#host s3650
s3650(config)#vlan 10
s3650(config-vlan)#name v10
s3650(config-vlan)#exit
s3650(config)#vlan 20
s3650(config-vlan)#name v20
s3650(config-vlan)#exit
s3650(config)#int fa0/10
s3650(config-if)#switchport access vlan 10
s3650(config-if)#exit
s3650(config)#int fa0/20
s3650(config-if)#switchport access vlan 20
s3650(config-if)#exit
s3650(config)#int vlan 10
%LINK-5-CHANGED: Interface Vlan10, changedstate to up
%LINEPROTO-5-UPDOWN: Line protocol onInterface Vlan10, changed state to up
s3650(config-if)#ip address 192.168.1.1255.255.255.0
s3650(config-if)#no shut
s3650(config-if)#exit
s3650(config)#int vlan 20
s3650(config-if)#
%LINK-5-CHANGED: Interface Vlan20, changedstate to up
s3650(config-if)#ip address 192.168.3.1255.255.255.0
s3650(config-if)#no shut
s3650(config-if)#router ospf 1
s3650(config-router)#network 192.168.1.00.0.0.255 area 0
s3650(config-router)#network 192.168.3.00.0.0.255 area 0
s3650(config-router)#exit
s3650(config)#exit
s3650#
%SYS-5-CONFIG_I: Configured from console byconsole
R1配置:
Router>en
Router#config t
Enter configuration commands, one perline. End with CNTL/Z.
Router(config)#host R1
R1(config)#int fa0/0
R1(config-if)#ip address 192.168.3.2255.255.255.0
R1(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0,changed state to up
%LINEPROTO-5-UPDOWN: Line protocol onInterface FastEthernet0/0, changed state to up
R1(config-if)#exit
R1(config)#int serial2/0
R1(config-if)#clock rate 64000
R1(config-if)#ip address 192.168.4.1255.255.255.0
R1(config-if)#no shut
%LINK-5-CHANGED: Interface Serial2/0,changed state to down
R1(config-if)#exit
R1(config)#router ospf 1
R1(config-router)#network 192.168.3.00.0.0.255 area 0
R1(config-router)#network
01:10:13: %OSPF-5-ADJCHG: Process 1, Nbr192.168.3.1 on FastEthernet0/0 from LOADING to FULL, Loading Done
% Incomplete command.
R1(config-router)#network 192.168.4.00.0.0.255 area 0
R1(config-router)#
R2配置:
Router>en
Router#config t
Enter configuration commands, one perline. End with CNTL/Z.
Router(config)#host R2
R2(config)#int fa0/0
R2(config-if)#ip address 192.168.2.1255.255.255.0
R2(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0,changed state to up
%LINEPROTO-5-UPDOWN: Line protocol onInterface FastEthernet0/0, changed state to up
R2(config-if)#exit
R2(config)#int serial2/0
R2(config-if)#ip address 192.168.4.2255.255.255.0
R2(config-if)#no shut
R2(config-if)#
%LINK-5-CHANGED: Interface Serial2/0,changed state to up
R2(config-if)#exit
R2(config)#
%LINEPROTO-5-UPDOWN: Line protocol onInterface Serial2/0, changed state to up
R2(config)#router ospf 1
R2(config-router)#network 192.168.2.00.0.0.255 area 0
R2(config-router)#network 192.168.4.00.0.0.255 area 0
R2(config-router)#exit
R2(config)#
测试:
从pc2 pingpc1.不通
在s3650上配置:
s3650#config t
Enter configuration commands, one perline. End with CNTL/Z.
s3650(config)#ip routing
s3650(config)#exit
s3650#
此时测试已通
相关文章推荐
- 第11章 路由器OSPF动态路由配置
- 第11章 路由器OSPF动态路由配置
- 第11章 路由器OSPF动态路由配置
- Packet Tracer 5.0实验(十) 路由器OSPF动态路由配置
- 实验十 路由器OSPF动态路由配置
- 路由器OSPF动态路由配置
- 实验十 路由器OSPF动态路由配置
- 第11章,Cisco Packet Tracer系列之--路由器OSPF动态路由配置
- 路由器OSPF动态路由配置
- Packet Tracer 5.0实验(十) 路由器OSPF动态路由配置
- cisco路由器基本实验之三 动态路由之RIP协议的配置(Boson NetSim)
- 在各路由器进行OSPF的基本配置
- 思科路由器配置ospf汇总和缺省路由发布
- Cisco PT模拟实验(14) 路由器OSPF动态路由的配置
- 路由器OSPF协议的配置 CISCO之CCNA篇实验之四
- Junos路由器静态路由及动态路由rip和ospf配置测试
- 实验九 路由器RIP动态路由配置
- 思科路由器配置ospf等价负载均衡
- cisco路由器基本实验之三 动态路由之RIP协议的配置(Boson NetSim)
- 路由器OSPF配置