error LNK2011: precompiled object not linked in; image may not run 问题解决方法
2013-01-04 00:45
567 查看
为了方便大家做实验,免得一个一个去试,做这里我把每个设备支持的模块的信息都写出来.(bat文件)
(针对刚刚接触dynamips不久的朋友)
注意:保证你的IOS版本在12.2S以上,在模拟交换时候为了保证实验能成功.IOS版本在12.3以上
首先从C7200开始
Slot 0:
C7200-IO-FE <------> 支持1个Fastethernet接口
C7200-IO-2FE <------> 支持2个 Fastethernet接口 (DynamipsGUI 2.3 里面没有这个选项,想用只有自己添加了)
C7200-IO-GE-E <------> 插这个卡以后会同时出现2个端口,Ethernet0/0和GigabitEthernet0/0 (反正我没有用到过这个卡)
注意:这三个卡只允许插在Slot0口,如果插入后面的slot口是无效的.
Slot 1-5:
PA-2FE-TX <------> 支持2个Fastethernet接口
PA-FE-TX <------> 支持1个Fastethernet接口
PA-4E <------> 支持4个Ethernet接口
PA-4T+ <------> 支持4个serial接口
PA-8E <------> 支持8个Ethernet接口
PA-8T <------> 支持8个serial接口
PA-A1 <------> 支持1个ATM port adapter接口
PA-GE <------> 支持1个GigabitEthernet接口
PA-POS-OC3<------> 支持1个Packet Over SONET/SDH接口(用于更高速度的接口)
然后是C3600(3620/3640/3660)
NM-16ESW <------> 支持16个Fastethernet接口(交换模块,在使用此模块做交换实验时候,请使用no ip routing 关闭端口路由)
NM-1E <------> 支持1个Ethernet接口
NM-1FE-TX<------> 支持1个Fastethernet接口
NM-4E <------> 支持4个Ethernet接口
NM-4T <------> 支持4个serial接口
Leopard-2FE<------>支持2个Fastethernet接口(3660专用,并且只能在slot 0 下使用)
注意:3620只能使用2个slot,3640可以使用4个slot,除Leopard-2FE模块做了限制,其他模块没有做限制插具体哪个slot.(DynamipsGUI里对slot已经做了限制,最近DynamipSeeV2.0已经发布了,但是里面不支持3660)
c3725/c3745/c2691
GT96100-FE <------>支持2个Fastethernet接口(只限制在slot 0)
NM-16ESW <------>支持16个Fastethernet接口(不做重复说明)
NM-1FE-TX <------>支持1个Fastethernet接口
NM-4T <------>支持4个serial接口
c2600(2610/2611/2620/2621/2610XM/2620XM/2650XM)
NM-16ESW <------> 支持16个Fastethernet接口
NM-1E <------> 支持1个Ethernet接口
NM-1FE-TX<------> 支持1个Fastethernet接口
NM-4E <------> 支持4个Ethernet接口
CISCO2600-MB-2E<------>支持2个Ethernet接口
CISCO2600-MB-2FE<------>支持2个Fastethernet接口
注>DynamipsGUI里的模块CISCO2600-MB-2E,CISCO2600-MB-2FE,并且只有2620类型可选
Dynamipsee里有2610/2611/2620/2621/2610XM/2620XM/2650XM类型选择.但没有2610/2611/2620/2621/2610XM/2620XM/2650XM
建议找个小的IOS把2600模拟成主机用 C2600IOS
(针对刚刚接触dynamips不久的朋友)
注意:保证你的IOS版本在12.2S以上,在模拟交换时候为了保证实验能成功.IOS版本在12.3以上
首先从C7200开始
Slot 0:
C7200-IO-FE <------> 支持1个Fastethernet接口
C7200-IO-2FE <------> 支持2个 Fastethernet接口 (DynamipsGUI 2.3 里面没有这个选项,想用只有自己添加了)
C7200-IO-GE-E <------> 插这个卡以后会同时出现2个端口,Ethernet0/0和GigabitEthernet0/0 (反正我没有用到过这个卡)
注意:这三个卡只允许插在Slot0口,如果插入后面的slot口是无效的.
Slot 1-5:
PA-2FE-TX <------> 支持2个Fastethernet接口
PA-FE-TX <------> 支持1个Fastethernet接口
PA-4E <------> 支持4个Ethernet接口
PA-4T+ <------> 支持4个serial接口
PA-8E <------> 支持8个Ethernet接口
PA-8T <------> 支持8个serial接口
PA-A1 <------> 支持1个ATM port adapter接口
PA-GE <------> 支持1个GigabitEthernet接口
PA-POS-OC3<------> 支持1个Packet Over SONET/SDH接口(用于更高速度的接口)
然后是C3600(3620/3640/3660)
NM-16ESW <------> 支持16个Fastethernet接口(交换模块,在使用此模块做交换实验时候,请使用no ip routing 关闭端口路由)
NM-1E <------> 支持1个Ethernet接口
NM-1FE-TX<------> 支持1个Fastethernet接口
NM-4E <------> 支持4个Ethernet接口
NM-4T <------> 支持4个serial接口
Leopard-2FE<------>支持2个Fastethernet接口(3660专用,并且只能在slot 0 下使用)
注意:3620只能使用2个slot,3640可以使用4个slot,除Leopard-2FE模块做了限制,其他模块没有做限制插具体哪个slot.(DynamipsGUI里对slot已经做了限制,最近DynamipSeeV2.0已经发布了,但是里面不支持3660)
c3725/c3745/c2691
GT96100-FE <------>支持2个Fastethernet接口(只限制在slot 0)
NM-16ESW <------>支持16个Fastethernet接口(不做重复说明)
NM-1FE-TX <------>支持1个Fastethernet接口
NM-4T <------>支持4个serial接口
c2600(2610/2611/2620/2621/2610XM/2620XM/2650XM)
NM-16ESW <------> 支持16个Fastethernet接口
NM-1E <------> 支持1个Ethernet接口
NM-1FE-TX<------> 支持1个Fastethernet接口
NM-4E <------> 支持4个Ethernet接口
CISCO2600-MB-2E<------>支持2个Ethernet接口
CISCO2600-MB-2FE<------>支持2个Fastethernet接口
注>DynamipsGUI里的模块CISCO2600-MB-2E,CISCO2600-MB-2FE,并且只有2620类型可选
Dynamipsee里有2610/2611/2620/2621/2610XM/2620XM/2650XM类型选择.但没有2610/2611/2620/2621/2610XM/2620XM/2650XM
建议找个小的IOS把2600模拟成主机用 C2600IOS
相关文章推荐
- error LNK2011: precompiled object not linked in; image may not run 问题解决方法
- issue---bug fix---error LNK2011: precompiled object not linked in; image may not run
- error LNK2011: precompiled object not linked in; image may not run
- Fatal error: Using $this when not in object context in 解决方法
- malloc: *** error for object xx: pointer being freed was not allocate的问题的解决方法之一
- vs2008编译时出现问题解决方法:MSVCRTD.lib(crtexew.obj) : error LNK2019: unresolved external symbol _WinMain@16 referenced in function ___tma
- Latex error "Not enough room in an internal buffer" 解决方法
- PL/SQL Developer 中的问题:Initialization error Could not load ".../oci.dll"解决方法
- 解决问题 “error: `cout' was not declared in this scope”
- Latex error "Not enough room in an internal buffer" 解决方法
- spring boot could not resolve placeholder in string value 问题解决方法
- Latex error "Not enough room in an internal buffer" 解决方法
- 【Angular学习】Angular4 ng serve报错:ERROR in AppModule is not an NgModule解决方法
- algorithm.sty not found error in LaTeX 解决方法
- [置顶] 解决vux 引入组件时Error in render function: "TypeError: _vm.$t is not a function"问题
- libcmtd.lib(crt0dat.obj) : error LNK2005: _exit already defined in msvcrtd.lib(MSVCRTD.dll) 编译错误解决方法
- Latex error "Not enough room in an internal buffer" 解决方法
- Windows下pip安装及更新出现“UnicodeEncodeError: 'ascii' codec can't encode character u'\u258c' in position 8: ordinal not in range(128)”问题解决办法
- SilverLight Canvas is not support in wpf 的问题解决方法
- VS2010 出现错误提示“Error Creating Control - Object reference not set to an instance of an objec” 的解决方法