AIX bootinfo命令
2012-10-28 22:12
302 查看
bootinfo 没有MAN手册
# man bootinfo
Manual entry for bootinfo not found or not installed.
官方网站也没有找到,不过有一个相同的提问:
http://www-01.ibm.com/support/docview.wss?uid=isg3T1010828
文章中列出了用getconf获取相同信息的命令示例:
getconf DISK_PARTITION /dev/hdisk0 这条命令没找到对应的bootinfo命令
摘抄网络的部分命令及说明:
# man bootinfo
Manual entry for bootinfo not found or not installed.
官方网站也没有找到,不过有一个相同的提问:
http://www-01.ibm.com/support/docview.wss?uid=isg3T1010828
文章中列出了用getconf获取相同信息的命令示例:
getconf DISK_PARTITION /dev/hdisk0 这条命令没找到对应的bootinfo命令
What was the device the system was last booted from? $ getconf BOOT_DEVICE hdisk0 # bootinfo -b hdisk0 What size is a particular disk in the system? $ getconf DISK_SIZE /dev/hdisk0 10240 # bootinfo -s hdisk0 140013 What partition size is being used on a disk in the system? $ getconf DISK_PARTITION /dev/hdisk0 16 Is the machine capable of running a 64-bit kernel? $ getconf HARDWARE_BITMODE 64 #bootinfo -y 64 Is the system currently running a 64-bit or 32-bit kernel? $ getconf KERNEL_BITMODE 64 # bootinfo -K 64 How much real memory does the system have? $ getconf REAL_MEMORY 524288 # bootinfo -r 16056320
摘抄网络的部分命令及说明:
bootinfo -s hdisk0 返回磁盘大小,可以是本地磁盘,也可以是存储的磁盘,单位是mb bootinfo -k(小写) 返回当前的启动模式/返回机器的钥匙的位置 1 Key is in Secure position. 2 Key is in Service position. 3 Key is in Normal position. bootinfo -K(大写) 返回当前系统运行的内核为32位还是64位 bootinfo -m 返回机器类型码 bootinfo -c -c Displays bootp daemon reply packet information stored with IPL control block. bootinfo -t 返回当前启动类型 1 Disk boot 3 CD-ROM boot 4 Tape boot 5 Network boot bootinfo -z 返回机器是否支持多处理器 0 不支持 1 支持 bootinfo -T 返回机器的硬件平台类型,比如rspc bootinfo -r 返回实际内存容量,单位为kbytes bootinfo -b 返回最后一次启动的设备 bootinfo -y 返回机器硬件是32位还是64位 bootinfo -e 是否可以从磁带启动 1 是 0 否
相关文章推荐
- AIX bootinfo命令
- aix的bootinfo命令。
- uboot中的mmc命令
- u-boot分析 七 (添加u-boot命令,学习u-boot命令实现原理)
- AIX 常用命令
- AIX常用命令集锦
- 使用info命令查看Redis信息和状态
- u-boot-2009.08在mini2440上的移植(四)---增加DM9000驱动和命令自动补全功能
- uboot mmc read/write命令用法
- 第十四期 U-Boot命令原理《路由器就是开发板》
- uboot源码分析(1)uboot 命令解析流程简析
- AIX常用命令
- AIX常用命令
- U-BOOT Nand命令支持(一)
- Aix iostat命令解析
- 在u-boot中添加命令
- 移植u-boot1.1.4支持操作nandFlash的nand erase命令
- u-boot中添加自定义命令
- uboot mmc read/write命令用法
- Gradle 命令之 --stacktrace , --info , --debug 用法