OCS LYNC: Asterisk 1.6 with OCS 2007 OR LYNC 2010
2012-10-08 13:50
281 查看
OCS LYNC: Asterisk 1.6 with OCS 2007 OR LYNC 2010
2010-12-20 11:07:12| 分类:MS-OCS | 标签:asterisk ocs lync
|字号大中小 订阅
original URL:
http://blogs.technet.com/b/gclark/archive/2008/10/09/asterisk-1-6-with-office-communications-server-2007.aspx?PageIndex=1#comments
I’ve personally been waiting for this release of Asterisk for some time now! After researching a little, I found out that Asterisk 1.6 now supports TCP & TLS. Currently it is still considered experimental – but hey, it’s always fun to play!
For those of you who are only familiar with Trixbox or FreePBX, there is no support for any graphical interface on 1.6 as of yet. But,I will keep this simple and to the point. Installing Asterisk on a Linux box with Kernel 2.6 is fairly straightforward.
In this Lab, I deployed
CentOS 5 - Kernel 2.6.18with Asterisk 1.6. When installing the OS you will also need the Kernel Sources and Kernel Headers packages.
First step of course is to build a Linux Box – I built mine in a VM, but installing on hardware will work just the same.
You can download Asterisk from www.asterisk.org. On your Linux box make a directory under /usr/src – called pbx. From that directory you can use the
following command:
wget http://downloads.digium.com/pub/asterisk/releases/asterisk-1.6.0.tar.gz
Next step is to unpack the package:
tar zxvf asterisk-1.6.0.tar.gz
With that done – we use the common method to build the source:
Change into that directory – cd asterisk-1.6.0
./configure
make
make install
make config
make samples
Start Asterisk by running /etc/init.d/asterisk start
Then run asterisk –vr. This will bring you into the Asterisk CLI:
note: in my testing, I directly install asterisknow 1.7 on VMware workstation 7.
Now you know Asterisk is up and running and we can get into modifying some configuration files. For this Lab there are only 2 files we need to be concerned with; SIP.CONF & EXTENSIONS.CONF which can be found under /etc/asterisk.
Starting with the Sample Config files that were created we can
just select and delete everything and then paste these example configs in:
SIP.CONF
[general]
context = default
bindport = 5060
bindaddr = 0.0.0.0
tcpbindaddr = 0.0.0.0
tcpenable = yes
[SIP_TRUNK]
type = peer
host = 10.100.16.78
qualify = yes
transport = tcp,udp
[5001]
type = friend
callerid = Linux User <5001> //the best is to change to 5001.
secret = 5001 //password must be 6 digits or you can't register to asterisk
host = dynamic
canreinvite = no
dtmfmode = rfc2833
mailbox = 5001
disallow = all
allow = ulaw
transport = udp
EXTENSIONS.CONF
[general]
static=yes
writeprotect=no
[globals]
[default]
exten => _+XXXX,1,Answer()
exten => _+XXXX,n,Set(CALLERID(name)=You Did It)
exten => _+XXXX,n,Set(CALLERID(num)=${CALLERID(num):1})
exten => _+XXXX,n,Goto(${EXTEN:1},1)
exten => 5001,1,Answer()
exten => 5001,n,Dial(SIP/5001,20,tr)
exten => 5001,n,Hangup
include => outbound
[outbound]
exten => _NXXNXXXXXX,1,Set(EXT=+${EXTEN}) //change _NXXNXXXXXX to 1XXX
exten => _NXXNXXXXXX,n,Dial(SIP/SIP_TRUNK/${EXT})
//change _NXXNXXXXXX to 1XXX
exten => _NXXNXXXXXX,n,Busy //change _NXXNXXXXXX to 1XXX
access asterisk web site http://astersikserverip and then apply configurations.
SoftPhone
Next we will use
X-Lite SoftPhone to register extension 5001 to Asterisk.
Configure the SIP Account on the SoftPhone:
When you hit the Apply button you will be registering the SoftPhone with Asterisk:
You can also see the registered extension from the Asterisk CLI/Console:
OCS 2007 configurations:
Now onto the OCS Configuration (In my lab I have a single SE server, and I installed a
Mediation Server). Let’s start with the Mediation Server.
As you see below, there are 2 IP Addresses on the Mediation Server. Both of them are on the same network. Of course you can place them on different networks if needed. Note, if they are in the same Network make sure that the External or PSTN facing interface
set to not register with your internal DNS:
On the Next Hop Connections Screen, you can see that we are pointing this back to the Asterisk PBX and the Inbound Routing is pointing back to the OCS Pool.
The Mediation Server configuration is not any different than other configuration when setting up Enterprise Voice pointing to any other SIP Gateway.
Now, onto the Global Forest Property and Pool configurations.
I have added this Location Profile Normalization Rule for this test:
Now that you have a Normalization Rule built you will need to make a Policy and Route. Here is an example of the Route I built for Testing:
One final step before making a call from the OCS MOC Client to the Softphone is to configure your OCS User for Enterprise Voice.
Under your OCS Pool, select Users then right click to get to the Properties of the user. Click Configure on the User Properties Screen.
When you log in from you MOC 2007 Client, you will be able to dial 5001. This will get normalized to +5001 and Dial out via the Mediation Server then through Asterisk to the SoftPhone.
LYNC 2010 configurations:
Dialplan:
Voice Policy:
Voice Route:
PSTN Usage:
Trunk:
On the PC with the SoftPhone you will a pop-up for the call will appear and you can answer or ignore it:
Integrating ocs 2007:
integrating lync 2010:
//bob is lync 2010 user
// display lync 2010 user and extension
Now let’s make a call in the other direction. On the “MOC Side” you will get the toast indicating a call is coming in:
integrating OCS 2007:
Integrating LYNC 2010:
// IF YOU Configure callerid = 5001 in sip.conf
//if your callerid = Linux User <5001> in sip.conf
Well that’s about it! I am sure I could have gone into more detail regarding setting up OCS and the Mediation server. But I wanted to concentrate on showing how to configure Asterisk, since the configuration for OCS is the same as when configuring it for
any other SIP Proxy/SIP Trunk (Mediation Server/Media Gateway).
Also there is so much you can do with
Asterisk. No physical TDM cards were used, but in a production environment one could easily add Analog and/or T1 TDM and make phone calls across the PSTN.
相关文章推荐
- 从OCS 2007 R2迁移到LYNC 2010 推荐
- 从OCS 2007 R2迁移至Lync Server 2010
- 让LYNC 2010 登录OCS 2007 R2
- Lync Server 2010的部署系列_第二十章 将OCS 2007 R2迁移至Lync Server 2010 推荐
- 配置OCS 2007 R2和LYNC 2010之间的联盟
- Reading and writing to Excel 2007 or Excel 2010 from C#
- outlook 2007 or 2010 的OLK 4文件夹在WIN 7系统存放在哪儿?
- OCS 2007 R2 与Lync 2013组织建立联盟
- OCS 2007、LYNC和正则表达式
- Exch UM: How to integrate Exchange 2010 (or 2007) with Trixbox 2.8
- LIT 4.0 (OCS 2007/R2 & Lync聊天记录查询)
- Windows Server 2008 R2下集成Exchange 2010 OWA与OCS 2007 R2
- Windows Server 2008 R2下部署Exchange 2010 UM和OCS 2007 R2中介服务器
- Windows Server 2008 R2下语音集成OCS 2007 R2 与Exchange 2010
- OCS 2007与Lync 2013的一点碎碎念
- Ocs 2007 迁移到 Lync的一些注意事项
- OCS(office commmunication server 2007)企业版部属测试二关于通讯簿
- Epplus 操作Excel 2007/2010
- Contact Selector in InfoPath 2007 and 2010
- Lync 2010移动客户端功能介绍及需求对比