SATA port selector and port muliplier 产品
2012-04-16 13:43
183 查看
SPM391PS
2 to 4 SATA RAID Controller with port selectorHighlights2-to-4 SATA(Port Selector + Port Multiplier)
Supports 6-port 3.0Gbps SATA II interface
OS independent Hardware RAID
Supports RAID levels: 0 / 1 / 10 / PM / Large (JBOD)
Provides RAID Manager GUI Utility to configure and monitor the status of the disks connected on RAID controller
Supports Hot Spare on RAID
Supports more than 2TB RAID drive
Rebuild speed: 200GB/hour
IntroductionSPM391PS is a Two-to-Four SATA RAID Controller. It integrated Port Selector, Port Multiplier and RAID processor to provide SATA port expansion, data protection, performance aggregation, and dual-host I/O control in various applications
SPM391PS provides four modes:
PM (Port Multiplier) Mode
RAID 0 Mode
RAID 1 & RAID 10 Mode: RAID 1 (for two disks) and RAID 10 (for four disks)
Large (JBOD) Mode
With an easy configuration scheme, the device can function as a pure port multiplier which provides SATA port expansion just like a SATA Hub, a hard drive performance booster which provides a high-performance device seen by the host controller, or a hard drive data protector which automatically backs up data to prevent data loss from hard drive damage.
The port selector enables two different hosts to control the four storage devices. The secondary host connection can be changed to use any one of several interfaces, such as 1394, USB, AOE, NAS, and others. The dual-host function may be used in storage subsystems, or for implementing a failover path in applications requiring redundancy. I/O priority is first given to the eSATA host; to enable control from the secondary host, the eSATA host must be disconnected.
SPM391PS also has an advanced mode to provide both the benefits of performance boost and data protection.
SPM391PS has a self-contained storage processor chip which completely frees up the main CPU loading and whose SATA ports comply with the eSATA specification, making it suitable for use in both internal system and external storage applications.
Technical Specifications
SATA Features | Supports 6-port 3.0Gbps SATA II interface Supports SATA II Gen2i and Gen2m (External SATA Connection, eSATA) Output swing control and automatic impedance calibration for SATA II PHY Supports asynchronous signal recovery Supports spread spectrum clocking Supports partial / slumber power saving mode Automatic speed negotiation for 3 Gbps or 1.5 Gbps Supports BIST and loopback mode Supports staggered spin-up Supports 48-bit LBA addressing Supports Native Command Queue (NCQ) Supports Hot-Plug Supports Asynchronous Notification Supports PM aware and non-PM aware host |
---|---|
RAID Features | Fully hardware-accelerated RAID Engine No driver, BIOS or software required for RAID operation No external DRAM or processor required for RAID operation Independent of device SATA port connection sequence Supports RAID levels: 0 / 1 / 10 / PM / Large (JBOD) SATA In-band application interface Supports more than 2TB RAID drive Supports on-line command based bad sector recovery Supports on-line Auto-Rebuild Rebuild speed: 200GB/hour Rebuild proceeds continuously between power cycling Supports various RAID configurations and monitoring methods |
Compliance | Compliant with Serial ATA II Port Multiplier Spec. Revision 1.1 Compliant with Serial ATA II PHY Electrical Spec. Revision 1.0 Compliant with Serial ATA High Speed Serialized AT Attachment Spec. Revision 2.5 |
DC Power Connector | Mini 4-pin Floppy Disk Drive like power Connector |
LEDs | Power Status LED RAID Status LED Host Status LED Device Status LEDs (Error, Activity&Link) |
[align=center]SPM391PS-SEH[/align] | [align=center]SPM391PS-SEV[/align] |
NAS Servers
Backup Systems
Disk Clone Systems
Serial ATA Enclosures
Large Capacity & High Performance Solid State Drive
Very Large Capacity Disk Systems
SATA Ports Expander
Physical Dimensions61.5(D) x 21.6(H) x 83.3(W)mm
SCSI I Connector Form Factor
PCI Bracket Form Factor
相关文章推荐
- sata port multiplier and port selector,NCQ
- Proxy and site on same port with Apache 2.2
- Effective Objective-C 2.0: Item 42: Prefer GCD to performSelector and Friends
- How to map host ip and port to Hyper-V
- 大家一起讨论简称论-关于简单Selector的制作与使用 (Production and Use)
- ASP.NET MVC with Entity Framework and CSS一书翻译系列文章之第六章:管理产品图片——多对多关系(上篇)
- Useful Products and Tools | 实用的产品和工具
- How SAS, Near Line (NL) SAS, and SATA disks compare
- SFB 项目经验-50-Lync-And-Cisco-功能-产品-对比
- tomcat 大并发报错 Maximum number of threads (200) created for connector with address null and port 8080
- socket udp client port get and set
- could not bind socket. address and port are already in use
- how to check port number and kill process with the port number
- [GUIDE]How To Port Different ROMS to Your Device (Simplest and Fastest)
- removeFromParentAndCleanup和callfuncN_selector
- Ask Premier Field Engineering (PFE) Platforms--The Slow Boot Case of the NetTCPPortSharing and NLA S
- HOW TO RUN YOUR WEB SERVER AND MQTT WEBSOCKETS BROKER ON THE SAME PORT
- TANDBERG视频会议产品价格
- Port Windows IPC apps to Linux, Part 2: Semaphores and events
- Could not bind socket. Address and port are already in use