思科无线AP胖瘦互转

原本想采用官方推荐的方法进行升级，不过感觉不怎么方便。官方的升级方法地址如下：
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html
麻烦之处有几点：1.每台胖AP都必须登录后配置用户密码、启动TELNET、配置接口地址等信息；2.虽然软件可以一次同时升级6台设备，但前提是你有一定的网络环境才可以；……

由于以上的几点，我采用了另外的一种方法进行胖AP升级到瘦AP。以下是整个升级过程：

准备工作：

1.Cisco TFTP Server程序并配置电脑IP为：10.0.0.2/255.0.0.0

2.准备瘦AP的IOS文件：如c1240-k9w7-tar.default；下载位置：
http://www.cisco.com/public/sw-center/index.shtml
操作过程：

按住AP上的MODEL按钮， 接通AP电源， 不要松开MODEL键，直至指示灯变为蓝色、黄色到粉色，在启动的过程中你会看到AP有一个默认IP地址为10.0.0.1, 而且会发送广播（发向255.255.255.255）寻找TFTP服务器，试图从TFTP服务器下载相对应的IOS（搜索与AP上默认文件名相同名称的文件，注意看AP上的信息，类似于“c1140-k9w7-tar.default”），

此时，你只需要将自己电脑的IP地址设置为10.0.0.0网段（和AP网段相同） 开启TFTP， 将瘦AP IOS文件名称改为和AP默认搜索的文件名完全相同，放在TFTP根目录下。 用网线将AP和电脑连接起来（先连接网线，否则不会发送广播查找TFTP，这里我一直在PC上PING10.0.0.1可是不通，不过不影响TFTP的正常工作）。
当搜索到相同文件名的文件后，会自动下载到AP中，并自动解压文件，利用此IOS重新启动， 自动重启后，胖AP就变成瘦AP了。
瘦AP转换为胖AP也可以用这种方法，简单，迅速， 只要预先设置好电脑IP，TFTP， 接通AP的网线， 按住MODEL键启动AP， 剩下的两分钟AP就自己搞定了。

注：如何识别胖瘦AP：

方法一：show version就可以出来AP系统版本信息，你要关注有如“c1140-k9w7、”的信息，看到系统的版本有” w7”，证明是胖AP.名称有”***w8”一定是瘦Ap。

1242 瘦AP IOS ：c1240-k9w7-tar.124-25d.JA.tar

1242 胖AP ios： c1240-rcvk9w8-tar.124-21a.JA2.tar

方法二： 用console线连接到AP上，启动后，能进入config terminal模式的就是胖AP，不能进去(也就是不可配置)的就是瘦AP。

AP升级日志：

Initializing ethernet port 0...

Reset ethernet port 0...

Reset done!

ethernet link up, 100 mbps, full-duplex

Ethernet port 0 initialized: link is up

button is pressed, wait for button to be released...

出现以下信息表示正在升级

process_config_recovery: set IP address and config to default 10.0.0.1

process_config_recovery: image recovery

image_recovery: Download default IOS tar image tftp://255.255.255.255/c1240-k9w7-tar.default

examining image...

extracting info (273 bytes)

Image info:

Version Suffix: rcvk9w8-

Image Name: c1240-rcvk9w8-mx

Version Directory: c1240-rcvk9w8-mx

Ios Image Size: 2632192

Total Image Size: 2632192

Image Feature: WIRELESS LAN|LWAPP|RECOVERY

Image Family: C1240

Wireless Switch Management Version: 3.0.51.0

Extracting files...

c1240-rcvk9w8-mx/ (directory) 0 (bytes)

extracting c1240-rcvk9w8-mx/c1240-rcvk9w8-mx (2622783 bytes)....................

................................................................................

................................................................................

................................................................................

................................................................................

................................................................................

................................................................................

.....................................................................

extracting c1240-rcvk9w8-mx/info (273 bytes)

extracting info.ver (273 bytes)

Deleting current version: flash:/c1240-k9w7-mx.124-3g.JA1...done.

New software image installed in flash:/c1240-rcvk9w8-mx

Configuring system to use new image...done.

Requested system reload in progress...download took about 108 seconds

Loading "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx"...###########################

################################################################################

################################################################################

######################################################################

File "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx" uncompressed and installed, entr

y point: 0x3000

executing...

按住MODE键，再插入电源开机。

出现button is pressed, wait for button to be released...时松开MODE键，貌似还要不停的敲回车，才能进 set command 模式，要不然会examining image...。

在出现AP：后，使用set IP_ADDR 10.0.0.1（设IP地址），set NETMASK 255.255.255.0（设掩码），tftp_init （格式化）。

在使用上述命令后，再使用TFTP从电脑上把文件拷下来，命令：tar -xtract tftp://10.0.0.2/c1240-k9w7-tar.124-10b.JA3.tar flash:

下载文件成功后，AP会自动安装。

安装完成后，输入boot重启AP。

Note Your wireless device configuration is not changed when using the CLI to reload the image file.

STEP 1: Open the CLI using a connection to the wireless device console port.

STEP 2: Reboot the wireless device by removing power and reapplying power.

STEP 3: Let the wireless device boot until it begins to inflate the image. When you see these lines on the CLI, press Esc:

Loading "flash:/c350-k9w7-mx.v122_13_ja.20031010/c350-k9w7-mx.v122_13_ja.20031010"

...###########################################################################

################################################################################

################################################################################

####################

STEP 4: When the ap: command prompt appears, enter the set command to assign an IP address, subnet mask,

and default gateway to the wireless device.

Note You must use upper-case characters when you enter the IP-ADDR, NETMASK, and DEFAULT_ROUTER options with the set command.

Your entries might look like this example:

ap: set IP_ADDR 192.168.133.160

ap: set NETMASK 255.255.255.0

ap: set DEFAULT_ROUTER 192.168.133.1

STEP 5: Enter the tftp_init command to prepare the wireless device for TFTP.

ap: tftp_init

STEP 6: Enter the tar command to load and inflate the new image from your TFTP server. The command must include this information:

? the -xtract option, which inflates the image when it is loaded

? the IP address of your TFTP server

? the directory on the TFTP server that contains the image

? the name of the image

? the destination for the image (the wireless device Flash)

Your entry might look like this example:

ap: tar -xtract tftp://192.168.130.222/images/c350-k9w7-tar.122-13.JA1.tar flash:

STEP 7: When the display becomes full, the CLI pauses and displays --MORE--. Press the spacebar to continue.

extracting info (229 bytes)

c350-k9w7-mx.122-13.JA1/ (directory) 0 (bytes)

c350-k9w7-mx.122-13.JA1/html/ (directory) 0 (bytes)

c350-k9w7-mx.122-13.JA1/html/level1/ (directory) 0 (bytes)

extracting c350-k9w7-mx.122-13.JA1/html/level1/appsui.js (558 bytes)

extracting c350-k9w7-mx.122-13.JA1/html/level1/back.htm (205 bytes)

extracting c350-k9w7-mx.122-13.JA1/html/level1/cookies.js (5027 bytes).

extracting c350-k9w7-mx.122-13.JA1/html/level1/forms.js (15704 bytes)...

extracting c350-k9w7-mx.122-13.JA1/html/level1/sitewide.js (14621 bytes)...

extracting c350-k9w7-mx.122-13.JA1/html/level1/config.js (2554 bytes)

extracting c350-k9w7-mx.122-13.JA1/html/level1/stylesheet.css (3215 bytes)

c350-k9w7-mx.122-13.JA1/html/level1/images/ (directory) 0 (bytes)

extracting c350-k9w7-mx.122-13.JA1/html/level1/images/ap_title_appname.gif (1422 bytes)

extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_button_1st.gif (1171 bytes)

extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_button_cbottom.gif (318 bytes)

extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_button_current.gif (348 bytes)

extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_button_last.gif (386 bytes)

extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_button_last_filler.gif (327 bytes)

extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_button_last_flat.gif (318 bytes)

extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_button_nth.gif (1177 bytes)

extracting c350-k9w7-mx.122-13.JA1/html/level1/images/apps_leftnav_dkgreen.gif (869 bytes)

-- MORE --

Note If you do not press the spacebar to continue, the process eventually times out and the wireless device stops inflating the image.

STEP 8: Enter the set BOOT command to designate the new image as the image that the wireless device uses when it reboots. The wireless device creates a directory for the image that has the same name as the image, and you must include the directory in the command. Your entry might look like this example:

ap: set BOOT flash:/c350-k9w7-mx.122-13.JA1/c350-k9w7-mx.122-13.JA1

STEP 9: Enter the set command to check your bootloader entries.

ap: set

BOOT=flash:/c350-k9w7-mx.122-13.JA1/c350-k9w7-mx.122-13.JA1

DEFAULT_ROUTER=192.168.133.1

IP_ADDR=192.168.133.160

NETMASK=255.255.255.0

STEP 10: Enter the boot command to reboot the wireless device. When the wireless device reboots, it loads the new image.

ap: boot