Cisco交换机密码破解方法
2011-06-24 16:42
197 查看
1.启用超级终端并出现连接界面。
2.拔掉交换机的电源。
3.按下交换机上的Mode按钮,与此同时,重新插上交换机的电源线。
4.当交换机左边的sys灯会慢慢的闪动,(细心的话会发现部分灯红色的闪过),按住mode按钮直到sys灯不闪动(常亮状态).否则提前松开的按钮的话会直接进入正常的启动,必须跳回步骤2重新来做。
5.可以松开Mode按钮。
之后系统将显示一些指示信息:
The system has been interrupted prior to initializing the flash file system. The following
commands will initialize the flash file system, and finish loading the operating system
software:
flash_init /---初始化flash文件系统---/
load_helper /---加载帮助文件---/
boot /---启动设备进入正常的模式---/
步骤:
switch:
Switch:flash_init
Switch:dir flash: /---查看Flash的文件名字可以用来确认文件名为config.text---/
Switch:rename flash:config.text flash:config.text.old /---把配置文件重命名,当然你可以不改为config.text.old,只要文件名和原来的不相同就可以---/
Switch:boot /---手动启动交换机---/
由于配置文件改过了,所以交换机找不到默认的config.text而出现配置的对话向导,选择n然后回车然后我们就会绕过原来的password而进入到:
Switch>
Switch>en /--可以进入特权模式--/
Switch#rename flash:config.text.old flash:config.text /---恢复交换机配置文件---/
Switch#copy flash:config.text system:running-config /---保存配置到DRAM里---/
Switch#config t
Switch(config)#no enable password /---干掉特权模式旧密码---/
Switch(config)#no enable secret /---干掉加秘密码---/
Switch(config)#exit
Switch#copy run start /---把当前配置的文件写回Flash---/
用这个方法修改密码不会把原来的配置文件内容清掉。特别是一个现成的大型网络里已经在运行的交换机,这样比较保险点。
2.拔掉交换机的电源。
3.按下交换机上的Mode按钮,与此同时,重新插上交换机的电源线。
4.当交换机左边的sys灯会慢慢的闪动,(细心的话会发现部分灯红色的闪过),按住mode按钮直到sys灯不闪动(常亮状态).否则提前松开的按钮的话会直接进入正常的启动,必须跳回步骤2重新来做。
5.可以松开Mode按钮。
之后系统将显示一些指示信息:
The system has been interrupted prior to initializing the flash file system. The following
commands will initialize the flash file system, and finish loading the operating system
software:
flash_init /---初始化flash文件系统---/
load_helper /---加载帮助文件---/
boot /---启动设备进入正常的模式---/
步骤:
switch:
Switch:flash_init
Switch:dir flash: /---查看Flash的文件名字可以用来确认文件名为config.text---/
Switch:rename flash:config.text flash:config.text.old /---把配置文件重命名,当然你可以不改为config.text.old,只要文件名和原来的不相同就可以---/
Switch:boot /---手动启动交换机---/
由于配置文件改过了,所以交换机找不到默认的config.text而出现配置的对话向导,选择n然后回车然后我们就会绕过原来的password而进入到:
Switch>
Switch>en /--可以进入特权模式--/
Switch#rename flash:config.text.old flash:config.text /---恢复交换机配置文件---/
Switch#copy flash:config.text system:running-config /---保存配置到DRAM里---/
Switch#config t
Switch(config)#no enable password /---干掉特权模式旧密码---/
Switch(config)#no enable secret /---干掉加秘密码---/
Switch(config)#exit
Switch#copy run start /---把当前配置的文件写回Flash---/
用这个方法修改密码不会把原来的配置文件内容清掉。特别是一个现成的大型网络里已经在运行的交换机,这样比较保险点。
相关文章推荐
- Cisco交换机密码破解方法
- Cisco交换机密码破解方法
- Cisco交换机密码破解方法
- ulock密码破解方法
- 忘记ftp密码使用python ftplib库暴力破解密码的方法示例
- 修改破解MYSQL密码方法大全
- 忘记ubuntu的root密码的破解方法,经实践有效!
- Linux各版本的本地root密码破解方法
- 各个linux版本root密码破解方法
- 常见文件密码破解方法大放送
- Centos 7.0 系统密码破解图文方法
- 三种方法破解系统管理员密码
- 计算机十二种常用密码的破解方法
- 九种破解Windows XP登录密码的方法
- 电信级的RSA加密后的密码的破解方法
- 电脑密码的十二种破解方法
- 破解root密码 方法2
- Linux本地root密码破解方法
- 如何取消Word文档保护密码(密码的破解方法)
- CISCO交换机密码破解