破解cisco交换机密码
2011-01-07 17:16
267 查看
1.启用超级终端并出现连接界面(就是除了交换机符号外空白一片那个哦)
2.拔掉交换机的电源.
3.按下交换机上的Mode按钮,与此同时,重新插上交换机的电源线.
4.当交换机左边的sys灯会慢慢的闪动,(细心的话会发现部分灯红色的闪过),按住mode按钮直到sys灯不闪动(常亮状态).否则提前松开的按钮的话会直接进入正常的启动,必须跳会步骤2
5.可以松开Mode按钮
之后系统将显示一些指示信息:
The system has been interrupted prior to initializing the flash file system.
The following
commands will initialize the flash file system, and finish loading the
operating system
software:
flash_init /---初始化flash文件系统---/
load_helper /---加载帮助文件---/
boot
/---启动设备进入正常的模式---/
步骤:
switch:
Switch:flash_init
Switch:dir flash:
/---查看Flash的文件名字可以用来确认文件名为config.text---/
Switch:rename flash:config.text
flash:config.text.old /---把配置文件重命名,当然你可以不改为config.text.old,只要文件名和原来的不相同就可以---/
Switch:boot
/---手动启动交换机---/
由于配置文件改过了,所以交换机找不到默认的config.text而出现配置的对话向导,选择n然后回车然后我们就会绕过原来的password而进入到:
Switch>
Switch>en /--可以进入特权模式--/
Switch#rename flash:config.text.old
flash:config.text /---恢复交换机配置文件---/
Switch#copy flash:config.text system:running-config
/---保存配置到DRAM里---/
Switch#config t
Switch(config)#no enable password /---干掉特权模式旧密码---/
Switch(config)#no enable secret /---干掉加秘密码---/
Switch(config)#exit
Switch#copy run start
/---把当前配置的文件写回Flash---/
用这个方法修改密码不会把原来的配置文件内容清掉。特别是一个现成的大型网络里已经在运行的交换机,这样比较保险点。
本文出自 “平哥_Jason” 博客,请务必保留此出处http://jasonliping.blog.51cto.com/471157/473966
2.拔掉交换机的电源.
3.按下交换机上的Mode按钮,与此同时,重新插上交换机的电源线.
4.当交换机左边的sys灯会慢慢的闪动,(细心的话会发现部分灯红色的闪过),按住mode按钮直到sys灯不闪动(常亮状态).否则提前松开的按钮的话会直接进入正常的启动,必须跳会步骤2
5.可以松开Mode按钮
之后系统将显示一些指示信息:
The system has been interrupted prior to initializing the flash file system.
The following
commands will initialize the flash file system, and finish loading the
operating system
software:
flash_init /---初始化flash文件系统---/
load_helper /---加载帮助文件---/
boot
/---启动设备进入正常的模式---/
步骤:
switch:
Switch:flash_init
Switch:dir flash:
/---查看Flash的文件名字可以用来确认文件名为config.text---/
Switch:rename flash:config.text
flash:config.text.old /---把配置文件重命名,当然你可以不改为config.text.old,只要文件名和原来的不相同就可以---/
Switch:boot
/---手动启动交换机---/
由于配置文件改过了,所以交换机找不到默认的config.text而出现配置的对话向导,选择n然后回车然后我们就会绕过原来的password而进入到:
Switch>
Switch>en /--可以进入特权模式--/
Switch#rename flash:config.text.old
flash:config.text /---恢复交换机配置文件---/
Switch#copy flash:config.text system:running-config
/---保存配置到DRAM里---/
Switch#config t
Switch(config)#no enable password /---干掉特权模式旧密码---/
Switch(config)#no enable secret /---干掉加秘密码---/
Switch(config)#exit
Switch#copy run start
/---把当前配置的文件写回Flash---/
用这个方法修改密码不会把原来的配置文件内容清掉。特别是一个现成的大型网络里已经在运行的交换机,这样比较保险点。
本文出自 “平哥_Jason” 博客,请务必保留此出处http://jasonliping.blog.51cto.com/471157/473966
相关文章推荐
- Cisco交换机密码破解方法
- Cisco交换机3750密码破解(一)
- Cisco交换机密码破解方法
- Cisco交换机密码破解方法
- Cisco交换机密码破解
- CISCO交换机密码破解
- Cisco交换机密码破解
- Cisco交换机之密码破解
- cisco交换机 2950 2960 3550等的密码破解
- Cisco交换机密码破解方法
- Cisco交换机路由器密码破解
- 图文详解破解linux Redhat 开机密码
- 动网论坛密码暴力破解程序代码
- 破解windows XP的登录密码
- 关于wordpress密码的破解思路
- 破解windows密码的方法
- 破解Linux系统密码
- AOPR破解密码速度怎么会变慢
- Excel—“撤销工作表保护密码”的破解并获取原始密码
- 九种破解Xp登录密码方法