Cisco 2960配置文档

Switch>en

Switch#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#hostname CETSFIS-F-CS2960-1C-33

CETSFIS-F-CS2960-1C-33(config)#exit

CETSFIS-F-CS2960-1C-33#vlan data

% Warning: It is recommended to configure VLAN from config mode,

as VLAN database mode is being deprecated. Please consult user

documentation for configuring VTP/VLAN in config mode.

CETSFIS-F-CS2960-1C-33(vlan)#vlan 100 name Management-VLAN

VLAN 100 added:

Name: Management-VLAN

CETSFIS-F-CS2960-1C-33(vlan)#vlan 2 name CET-C

VLAN 2 added:

Name: CET-C

CETSFIS-F-CS2960-1C-33(vlan)#vlan 4 name CET-E

VLAN 4 added:

Name: CET-E

CETSFIS-F-CS2960-1C-33(vlan)#vlan 34 name Area-F

VLAN 34 added:

Name: Area-F

CETSFIS-F-CS2960-1C-33(vlan)#exit

APPLY completed.

Exiting....

CETSFIS-F-CS2960-1C-33#conf t

CETSFIS-F-CS2960-1C-3(config)#int vlan 1

CETSFIS-F-CS2960-1(config-if)#shutdown

CETSFIS-F-CS2960-1(config-if)#int vlan 100

CETSFIS-F-CS2960-1(config-if)#no shutdown

CETSFIS-F-CS2960-1(config-if)#ip address 10.114.0.33 255.255.255.0

CETSFIS-F-CS2960-1(config-if)#exit

CETSFIS-F-CS2960-1C-3(config)#ip default-gateway 10.114.0.254

CETSFIS-F-CS2960-1C-3(config)#interface rang gi0/1 -2

CETSFIS-F-CS(config-if-range)#switchport mode trunk

CETSFIS-F-CS(config-if-range)#interface rang fa0/1 -48

CETSFIS-F-CS(config-if-range)#switchport mode access

CETSFIS-F-CS(config-if-range)#switchport access vlan 34

CETSFIS-F-CS(config-if-range)#spanning-tree portfast

%Warning: portfast should only be enabled on ports connected to a single

host. Connecting hubs, concentrators, switches, bridges, etc... to this

interface when portfast is enabled, can cause temporary bridging loops.

Use with CAUTION

%Portfast will be configured in 48 interfaces due to the range command

but will only have effect when the interfaces are in a non-trunking mode.

CETSFIS-F-CS(config-if-range)#exit

CETSFIS-F-CS2960-1C-3(config)#vtp domain SFIS

Changing VTP domain name from NULL to SFIS

CETSFIS-F-CS2960-1C-3(config)#vtp mode transparent

Setting device to VTP TRANSPARENT mode.

CETSFIS-F-CS2960-1C-3(config)#snmp-server community netteam ro

CETSFIS-F-CS2960-1C-3(config)#snmp-server community netteam%123 rw

CETSFIS-F-CS2960-1C-3(config)#logging 10.114.5.88

CETSFIS-F-CS2960-1C-3(config)#service timestamps log datetime localtime

CETSFIS-F-CS2960-1C-3(config)#clock timezone gmt +8

CETSFIS-F-CS2960-1C-3(config)#ntp server 10.114.5.100

CETSFIS-F-CS2960-1C-3(config)#line vty 0 4

CETSFIS-F-CS2960(config-line)#password xxxxxxx

CETSFIS-F-CS2960(config-line)#login

CETSFIS-F-CS2960(config-line)#exit

CETSFIS-F-CS2960-1C-3(config)#enable secret xxxxxxx

CETSFIS-F-CS2960-1C-3(config)#service password-encryption

CETSFIS-F-CS2960-1C-3(config)#end

CETSFIS-F-CS2960-1C-33#wr

CETSFIS-F-CS2960-1C-3(config)#line console 0

CETSFIS-F-CS2960(config-line)#logging synchronous