During bootup my computer hangs at "Verifying DMI pool data."

Computer Hangs at "Verifying DMI Pool Data"
Last updated: 3/9/04

Q. During bootup my computer hangs at "Verifying DMI pool data." What is it and how do I fix it?

A. DMI or DesktopManagement Interface (pdf) is a layer of abstraction between system components and the software that manages them. The System Management BIOS (SMBIOS) is an extension of the Basic Input Output System (BIOS) that formulates and delivers this information to the operating system. The pool data is the information. In short, when the BIOS is "Verifying DMI pool data" it is verifying the table of data it sends to the operating system (Windows, etc.). If it isn't sucessful, it should return an error. Wait a reasonable period of time for it to finish. It may make take some time or it may be stuck. Possible fixes:

1. If you changed the hardware just before this problem occurred (e.g., installed a new hard disk drive), unchange it.

2. If you installed a new hard disk drive, set the motherboard CMOS Setup to Auto for the drive type. You may have to disconnect the drive first.

3. Enable "Reset Configuration Data" (may be "Force Update ESCD" in some CMOS Setuups) in the motherboard CMOS Setup PNP/PCI configuration. (Rebooting will automatically disabled it after it has done its thing.)

4. The CMOS may be corrupted. Clear it.

5. Disconnect all drives not required to boot the computer. If this fixes it, reconnect one at time.

6. The floppy drive may be bad or not connected properly.

7. Reseat all expansion boards.

8. Pull all boards not required to boot the computer.

From:http://www.duxcw.com/faq/computer/dmi.html

----------------------------------------------------------------

from:http://www.computerhope.com/issues/ch000474.htm

Computer stops at verifying dmi pool data.

Issue:

Computer stops at verifying dmi pool data.

Cause:

This issue can be caused by any of the below reasons.

Corrupt boot files on the computer.

Settings for hard disk drive are not correct.

Floppy diskette or CD in computer causing issue.

Boot devices not set properly.

BIOS corrupt or misc. setting not set properly.

Connections loose or disconnected.

Bad Hard disk drive or other bad hardware.

Solution:

Corrupt boot files on the computer
If the computer has no bootable files on the drive it is attempting to boot from it is possible that the computer may halt at " verifying dmi pool data..."
To resolve this issue:

Boot from a bootable floppy diskette. Ensure that this diskette was made on the same Microsoft Windows operating system that is installed on your computer.

Once at the A:/> prompt type "sys c:" and press enter. This should report the message "File system transferred." Once transferred remove the diskette and reboot the computer.

If the computer continues to not boot attempt to re-create the master boot record by booting from the bootable floppy diskette again. Once at the A:/> prompt type "fdisk /mbr" and press enter. This should return you to the prompt without giving you any message. Once at the prompt remove the diskette and reboot the computer.
Additional information about the "fdisk /mbr" command can be found on document CH000175.
Note: The above information only applies to Microsoft Windows users. If you are running a Linux / Unix variant or other operating system such as OS/2 and the computer is freezing at this DMI message ensure that Linux / Unix has been properly installed first and/or your boot manger is not corrupt.
Settings for hard disk drive are not correct
The computer freezing at "Verifying dmi pool data..." may be caused when the hard disk drive settings withinCMOS are not set properly. Enter CMOS and verify that the hard disk drive settings are set properly and/or that it is set to Auto Detect. Additional information about entering CMOS setup is found on document CH000192.
Floppy diskette or CD in computer causing issue
Verify no floppy diskette or CD is in the computer. In some cases the computer may be trying to boot from either of these drives causing issues with the boot sequence.
Boot devices not set properly
The computer stopping at " verifying dmi pool data..." can be caused when the boot devices on your computer are not set properly in CMOS. First, verify that no CD or diskette is in your computer. If a CD or diskette is in the computer attempt to remove this first to determine if it was attempting to boot from it.
If No CD or diskette is in the computer and your computer still halts at the DMI message enter CMOS setup (steps found on document CH000192) and verify that the boot options are set properly. We commonly recommend that the floppy be set the first boot device, hard drive as the second boot device and the CD-ROM as the third boot device.
BIOS corrupt or misc. setting not set properly
If none of the above recommendations have resolved your issue attempt to reset the BIOS / CMOS settings to the factory or default settings. Additional information about how to do this can be found on document CH000976.
Connections loose or disconnected
If the computer has been recently moved or new hardware has been installed in the computer it is possible that a connection may be loose or even disconnected. Verify that the hard disk drive, floppy and CD-ROM cables are properly connected.
Bad hard disk drive or other bad hardware
If you computer continues to freeze at the DMI message after attempting all of the above recommendations it is possible that the computer may be freezing because of a bad hard disk drive or other bad hardware in the computer.
Before replacing any hardware we first recommend you attempt to erase everything on the hard drive and start over. Additional information about this process can be found on document CH000186.
If you're unable to get to the point of re-installing the operating system it's likely your computer has a hardware issue and it's suggested that the hard drive be replaced. If that doesn't resolve the issue then have the motherboard replaced.

Additional information:

See our CMOS help page for additional information and help with your computer CMOS.

See our DMI dictionary definition page for additional information about DMI.