3550交换机(EMI)配置维护手册(一)
2009-02-13 03:17
330 查看
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center]3550交换机(EMI)[/align]
[align=center]简明配置维护手册[/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center]目录[/align]
说明...3
产品特性...3
配置端口...4
配置一组端口...4
配置二层端口...6
配置端口速率及双工模式...6
端口描述...7
配置三层口...8
监控及维护端口...10
监控端口和控制器的状态...10
刷新、重置端口及计数器...12
关闭和打开端口...13
配置VLAN..14
理解VLAN..14
可支持的VLAN..15
配置正常范围的VLAN..15
生成、修改以太网VLAN..15
删除VLAN..17
将端口分配给一个VLAN..18
配置VLANTrunks19
使用STP实现负载均衡...22
支持VLAN
到1005个VLAN
支持VLANID从1到4094(IEEE802.1Q标准)
支持ISL及IEEE802.1Q封装
安全
支持IOS标准的密码保护
静态MAC地址映射
标准及扩展的访问列表支持,对于路由端口支持入出双向的访问列表,对于二层端口支持入的访问列表
支持基于VLAN的访问列表
3层支持(需要多层交换的IOS)
HSRP
IP路由协议
RIP versions1and2
OSPF
IGRP及EIGRP
BGP Version4
监视
交换机LED指示端口状态
SPAN及远端SPAN(RSPAN)可以监视任何端口或VLAN的流量
内置支持四组的RMON监控功能(历史、统计、告警及事件)
Syslog功能
其它功能:
支持以下的GBIC模块:
·1000BASE-TGBIC:铜线最长100m
·1000BASE-SXGBIC:光纤最长1804feet(550m)
·1000BASE-LX/LHGBIC:光纤最长32,808feet(6milesor10km)
·1000BASE-ZXGBIC:光纤最长328,084feet(62milesor100km)
当使用interfacerange命令时有如下的规则:
有效的组范围:
vlan从1到4094
fastethernet槽位/{firstport}-{lastport},槽位为0
gigabitethernet槽位/{firstport}-{lastport},槽位为0
port-channelport-channel-number-port-channel-number,port-channel号从1到64
端口号之间需要加入空格,如:interfacerangefastethernet0/1–5是有效的,而interfacerangefastethernet0/1-5是无效的.
interfacerange命令只能配置已经存在的interfacevlan
所有在同一组的端口必须是相同类别的。
见以下例子:
以下的例子显示使用句号来配置不同类型端口的组:
Usethenodescriptioninterfaceconfigurationcommandtodeletethedescription.
ThisexampleshowshowtoaddadescriptiononFastEthernetinterface0/4andtoverifythedescription:
SVIs:即interfacevlan
三层以太网通道口(EtherChannel)
.路由口:路由口是指某一物理端口在端口配置状态下用noswitchport命令生成的端口
所有的三层都需要IP地址以实现路由交换
配置步骤如下:
配置举例如下:
showipinterface命令:
举例如下:
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center]3550交换机(EMI)[/align]
[align=center]简明配置维护手册[/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center][/align]
[align=center]目录[/align]
说明
本手册只包括日常使用的有关命令及特性,其它未涉及的命令及特性请参考英文的详细配置手册。产品特性
3550EMI是支持二层、三层功能(EMI)的交换机支持VLAN
到1005个VLAN
支持VLANID从1到4094(IEEE802.1Q标准)
支持ISL及IEEE802.1Q封装
安全
支持IOS标准的密码保护
静态MAC地址映射
标准及扩展的访问列表支持,对于路由端口支持入出双向的访问列表,对于二层端口支持入的访问列表
支持基于VLAN的访问列表
3层支持(需要多层交换的IOS)
HSRP
IP路由协议
RIP versions1and2
OSPF
IGRP及EIGRP
BGP Version4
监视
交换机LED指示端口状态
SPAN及远端SPAN(RSPAN)可以监视任何端口或VLAN的流量
内置支持四组的RMON监控功能(历史、统计、告警及事件)
Syslog功能
其它功能:
支持以下的GBIC模块:
·1000BASE-TGBIC:铜线最长100m
·1000BASE-SXGBIC:光纤最长1804feet(550m)
·1000BASE-LX/LHGBIC:光纤最长32,808feet(6milesor10km)
·1000BASE-ZXGBIC:光纤最长328,084feet(62milesor100km)
配置端口
配置一组端口
命令 | 目的 | |
Step1 | configureterminal | 进入配置状态 |
Step2 | interfacerange{port-range} | 进入组配置状态 |
Step3 | 可以使用平时的端口配置命令进行配置 | |
Step4 | end | 退回 |
Step5 | showinterfaces[interface-id] | 验证配置 |
Step6 | copyrunning-configstartup-config | 保存 |
有效的组范围:
vlan从1到4094
fastethernet槽位/{firstport}-{lastport},槽位为0
gigabitethernet槽位/{firstport}-{lastport},槽位为0
port-channelport-channel-number-port-channel-number,port-channel号从1到64
端口号之间需要加入空格,如:interfacerangefastethernet0/1–5是有效的,而interfacerangefastethernet0/1-5是无效的.
interfacerange命令只能配置已经存在的interfacevlan
所有在同一组的端口必须是相同类别的。
见以下例子:
Switch#configureterminal
Switch(config)#interfacerangefastethernet0/1-5
Switch(config-if-range)#noshutdown
Switch(config-if-range)#
*Oct608:24:35:%LINK-3-UPDOWN:InterfaceFastEthernet0/1,changedstatetoup
*Oct608:24:35:%LINK-3-UPDOWN:InterfaceFastEthernet0/2,changedstatetoup
*Oct608:24:35:%LINK-3-UPDOWN:InterfaceFastEthernet0/3,changedstatetoup
*Oct608:24:35:%LINK-3-UPDOWN:InterfaceFastEthernet0/4,changedstatetoup
*Oct608:24:35:%LINK-3-UPDOWN:InterfaceFastEthernet0/5,changedstatetoup
*Oct608:24:36:%LINEPROTO-5-UPDOWN:LineprotocolonInterfaceFastEthernet0/05,
changedstatetoup
*Oct608:24:36:%LINEPROTO-5-UPDOWN:LineprotocolonInterfaceFastEthernet0/3,changed
statetoup
*Oct608:24:36:%LINEPROTO-5-UPDOWN:LineprotocolonInterfaceFastEthernet0/4,changed
statetoup
以下的例子显示使用句号来配置不同类型端口的组:
Switch#configureterminal
Switch(config)#interfacerangefastethernet0/1-3,gigabitethernet0/1-2
Switch(config-if-range)#noshutdown
Switch(config-if-range)#
*Oct608:29:28:%LINK-3-UPDOWN:InterfaceFastEthernet0/1,changedstatetoup
*Oct608:29:28:%LINK-3-UPDOWN:InterfaceFastEthernet0/2,changedstatetoup
*Oct608:29:28:%LINK-3-UPDOWN:InterfaceFastEthernet0/3,changedstatetoup
*Oct608:29:28:%LINK-3-UPDOWN:InterfaceGigabitEthernet0/1,changedstatetoup
*Oct608:29:28:%LINK-3-UPDOWN:InterfaceGigabitEthernet0/2,changedstatetoup
*Oct608:29:29:%LINEPROTO-5-UPDOWN:LineprotocolonInterfaceGigabitEthernet0/1,
changedstatetoup
*Oct608:29:29:%LINEPROTO-5-UPDOWN:LineprotocolonInterfaceFastEthernet0/2,
changedstatetoup
*Oct608:29:29:%LINEPROTO-5-UPDOWN:LineprotocolonInterfaceFastEthernet0/3,
changedstatetoup
配置二层端口
3550的所有端口缺省的端口都是二层口,如果此端口已经配置成三层端口的话,则需要用switchport来使其成为二层端口。配置端口速率及双工模式
可以配置快速以太口的速率为10/100Mbps及千兆以太口的速率为10/100/1000-Mbps;但对于GBIC端口则不能配置速率及双工模式,有时可以配置nonegotiate,当需要联接不支持自适应的其它千兆端口时
命令 | 目的 | |
Step1 | configureterminal | 进入配置状态. |
Step2 | interfaceinterface-id | 进入端口配置状态. |
Step3 | speed{10|100|1000|auto|nonegotiate} | 设置端口速率 注1000只工作在千兆口.GBIC模块只工作在1000Mbps下.nonegotiate只能在这些GBIC上用1000BASE-SX,-LX,and-ZXGBIC. |
Step4 | duplex{auto|full|half} | 设置全双工或半双工. |
Step5 | end | 退出 |
Step6 | showinterfacesinterface-id | 显示有关配置情况 |
Step7 | copyrunning-configstartup-config | 保存 |
Switch#configureterminal
Switch(config)#interfacefastethernet0/3
Switch(config-if)#speed10
Switch(config-if)#duplexhalf
端口描述
命令 | 目的 | |
Step1 | configureterminal | 进入配置模式 |
Step2 | interfaceinterface-id | 进入要加入描述的端口 |
Step3 | descriptionstring | 加入描述(最多240个字符). |
Step4 | end | 退回. |
Step5 | showinterfacesinterface-iddescription or showrunning-config | 验证. |
Step6 | copyrunning-configstartup-config | 保存 |
ThisexampleshowshowtoaddadescriptiononFastEthernetinterface0/4andtoverifythedescription:
Switch#configterminal
Enterconfigurationcommands,oneperline.EndwithCNTL/Z.
Switch(config)#interfacefastethernet0/4
Switch(config-if)#descriptionConnectstoMarketing
Switch(config-if)#end
Switch#showinterfacesfastethernet0/4description
InterfaceStatusProtocolDescription
Fa0/4updownConnectstoMarketing
配置三层口
Catalyst3550支持三种类型的三层端口:SVIs:即interfacevlan
Note当生成一个interfaceVlan时,只有当把某一物理端口分配给它时才能被激活 |
.路由口:路由口是指某一物理端口在端口配置状态下用noswitchport命令生成的端口
所有的三层都需要IP地址以实现路由交换
配置步骤如下:
命令 | 目的 | |
Step1 | configureterminal | 进入配置状态 |
Step2 | interface{{fastethernet|gigabitethernet}interface-id}|{vlanvlan-id}|{port-channelport-channel-number} | 进入端口配置状态 |
Step3 | noswitchport | 把物理端口变成三层口 |
Step4 | ipaddressip_addresssubnet_mask | 配置IP地址和掩码 |
Step5 | noshutdown | 激活端口 |
Step6 | end | 退出 |
Step7 | showinterfaces[interface-id] showipinterface[interface-id] showrunning-configinterface[interface-id] | 验证配置 |
Step8 | copyrunning-configstartup-config | 保存配置 |
Switch#configureterminal
Enterconfigurationcommands,oneperline.EndwithCNTL/Z.
Switch(config)#interfacegigabitethernet0/2
Switch(config-if)#noswitchport
Switch(config-if)#ipaddress192.20.135.21255.255.255.0
Switch(config-if)#noshutdown
Switch(config-if)#end
showipinterface命令:
Switch#showipinterfacegigabitethernet0/2
GigabitEthernet0/2isup,lineprotocolisup
Internetaddressis192.20.135.21/24
Broadcastaddressis255.255.255.255
Addressdeterminedbysetupcommand
MTUis1500bytes
Helperaddressisnotset
Directedbroadcastforwardingisdisabled
<outputtruncated>
监控及维护端口
监控端口和控制器的状态
主要命令见下表:ShowCommandsforInterfacesCommand | 目的 |
showinterfaces[interface-id] | 显示所有端口或某一端口的状态和配置. |
showinterfacesinterface-idstatus[err-disabled] | 显示一系列端口的状态或错误-关闭的状态 |
showinterfaces[interface-id]switchport | 显示二层端口的状态,可以用来决定此口是否为二层或三层口。 |
showinterfaces[interface-id]description | 显示端口描述 |
showipinterface[interface-id] | 显示所有或某一端口的IP可用性状态 |
showrunning-configinterface[interface-id] | 显示当前配置中的端口配置情况 |
showversion | 显示软硬件等情况 |
Switch#showinterfacesstatus
PortNameStatusVlanDuplexSpeedType
Gi0/1connectedrouteda-fulla-10010/100/1000Base
TX
Gi0/2wceserver20.20.2disabledroutedautoauto10/100/1000BaseTX
Gi0/3ipwccpweb-cachenotconnectroutedautoauto10/100/1000BaseTX
Gi0/4notconnectroutedautoauto10/100/1000BaseTX
Gi0/5notconnectroutedautoauto10/100/1000BaseTX
Gi0/6disabledroutedautoauto10/100/1000BaseTX
Gi0/7disabledroutedautoauto10/100/1000BaseTX
Gi0/8disabledroutedauto10010/100/1000BaseTX
Gi0/9notconnectroutedautoauto10/100/1000BaseTX
Gi0/10notconnectroutedautoauto10/100/1000BaseTX
Gi0/11disabledroutedautoautounknown
Gi0/12notconnectroutedautoautounknown
Switch#showinterfacesfastethernet0/1switchport
Name:Fa0/1
Switchport:Enabled
AdministrativeMode:staticaccess
OperationalMode:down
AdministrativeTrunkingEncapsulation:dot1q
NegotiationofTrunking:Off
AccessModeVLAN:1(default)
TrunkingNativeModeVLAN:1(default)
TrunkingVLANsEnabled:ALL
PruningVLANsEnabled:2-1001
Protected:false
Unknownunicastblocked:disabled
Unknownmulticastblocked:disabled
VoiceVLAN:dot1p(Inactive)
Appliancetrust:5
Switch#showrunning-configinterfacefastethernet0/2
Buildingconfiguration...
Currentconfiguration:131bytes
!
interfaceFastEthernet0/2
switchportmodeaccess
switchportprotected
noipaddress
mlsqoscos7
mlsqoscosoverride
end
相关文章推荐
- 3550交换机(EMI)简明配置维护手册
- 3550交换机(EMI)配置维护手册(二)
- cisco3550交换机(EMI)简明配置维护手册
- Oracle_dataguard__11G_配置与维护手册
- 2950交换机简明配置维护手册1
- cisco路由器配置及维护手册
- AIX系统维护手册二.双机配置,HACMP
- 4006交换机(IOS版)简明配置维护手册
- Cisco 2950交换机简明配置维护手册
- Cacti配置及维护指导手册
- cisco路由器配置及维护手册
- 2950交换机简明配置维护手册
- 思科6000系列交换机配置维护手册
- 2950交换机简明配置维护手册
- 思科6000系列交换机配置维护手册
- 2950交换机 简明配置维护手册
- 2950交换机简明配置维护手册
- Cognos环境配置手册(V 1.0.0)
- [转载]Informix Dynamic Server维护手册
- Hibernate参考手册学习与实践:配置