cisco路由器IOS灾难恢复
2009-01-22 14:20
489 查看
参考:CISCO IOS升级方法
Fastest Way to Recover or Upgrade Cisco IOS using tftpdnld
如果IOS被损坏,例如升级IOS过程中断电等。
可以在ROM monitor commands模式下通过2种方法恢复:xmodem 或者 tftpdnld
1.xmodem
xmodem—Use this if the computer attached to your console has a terminal emulator that has xmodem capability.
第一步:
先打开超级终端,进入rommon 模式(Ctrl+Break组合键),键入confreg, 如下:
rommon 1 > confreg 回车
onfiguration Summary
enabled are:
load rom after netboot fails
console baud: 9600
boot: image specified by the boot system commands or default to: cisco2-C2600
****显示
do you wish to change the configuration? y/n
: y (选择 yes)
enable "diagnostic mode"? y/n
: n (选择 no)
enable "use net in IP bcast address"? y/n
: n (选择 no)
disable "load rom after netboot fails"y/n
: n (选择 no)
enable "use all zero broadcast"? y/n
: n (选择 no)
enable "break/abort has effect"? y/n
: n (选择 no)
enable "ignore system config info"? y/n
: n (选择 no)
change console baud rate y/n
: y (选择 yes)
enter rate: 0 = 9600, 1= 4800, 2 = 1200, 3 = 2400 4 = 19200, 5 = 38400, 6 = 57600, 7 = 115200 [0]: 7 (选择 7,用最大的115200速率的xmodem传输)
change the boot characteristics? y/n
: n (选择 no)
Configuration Summary
enabled are:
load rom after netboot fails
console baud: 115200
boot: image specified by
the boot system commands or default to: cisco2-C2600
do you wish to change the configuration? y/n
: n (选择 no)
You must reset or power cycle for new config to take effect
rommon 2 > reset 回车
注意:在此时键入 reset键,然后再修改超级终端里设置端,重新建立一个超级终端连接之前,开始定义串口速度(我的电脑速率为115200,记住,一定这么做,(期间系统重新启动)启动后,出--端口属性----串口速度调为115200 ,否则出现乱码!
rommon 1> xmodem -cr
Do not start the sending program yet.
invoke this applicationonly for disaster recovery.
Do you wish to continue? y/n
: y (选择 yes)
Ready to receive file
此时,在超级终端的菜单上的“传送”---xmodem”协议,点击“发送”即可发送文件”----选择IOS镜像文件所在地以及选择使用“然后等待10-20分钟左右就把3-6M的IOS灌进去了
!!!! 会自动引导IOS(c2600-i-mz.122-8.T10.bin),进入EN模式,show flash: ,会发现损坏的IOS版本被删除,其实只是做了一个1 5850064 c2600-i-mz.122-8.T10.bin(delected)的标志,在EN模式下,用
squeeze flash:c2600-i-mz.122-8.T10.bin物理删除它。(#######¥¥¥¥¥记住一定不要重起)
其实IOS没有倒入,是调用的配置文件。
show flash:
会发现IOS没有
(#######¥¥¥¥¥记住一定不要重起)
第二步:倒入IOS
手动把E0/1用直连线插到交换机上,笔记本的网卡也用直连线也插到交换机上
en
show run
conf t
int fa0/1
ip add 192.168.0.2 255.255.255.0
no shu
exit
exit
wr
笔记本网卡设置成192.168.0.1 255.255.255.0
在ROUTE上 ping 192.168.0.1
打开TFTP,把IOS拷贝到TFTP目录下(c2600-i-mz.122-8.T10.bin)
en
copy tftp flash:c2600-i-mz.122-8.T10.bin
完毕后
show flash
(!!!!!绝对不能重起)
看到版本c2600-i-mz.122-8.T10.bin,后面没有delected
倒入成功
conf t
config-register 0x2102
boot system flash c2600-i-mz.122-8.T10.bin
exit
exit
wr
reload
会引导到正常的操作模式下,成功
第三步:
改到9600,可要可不要
方法2:tftpdnld tftpdnld—Use this if you have a TFTP server directly connected to the Ethernet 0 port.
1、用Cisco原配的线缆连接路由器的console口与PC机的COM1,使用PC机的超级终端软件访问路由器;用一根双绞线连接路由器的eth0/0口与PC机的网卡。
2、将路由器的eth0/0口IP地址设为10.32.10.32;PC机的IP地址设为10.32.10.1.将要升级的IOS映象文件拷贝到相关的目录中,并运行TFTP服务器软件,通过菜单设置Root目录为拷贝IOS映象文件所在目录。
3、通过set 命令查看配置参数
QUOTE:rommon 2 > set
PS1=rommon ! >
BOOT=
BSI=0
RET_2_RTS=
?=0 4、在 rommon 状态下输入:(注意大小写)
QUOTE:rommon 3 >IP_ADDRESS=10.32.10.1 (路由器的ip地址)
rommon 4 >IP_SUBNET_MASK=255.255.255.0 (路由器的掩码)
rommon 5 >DEFAULT_GATEWAY=10.32.10.32 (缺省网关,是pc机的ip地址)
rommon 6 >TFTP_SERVER=10.32.10.32 (是pc机的ip地址)
rommon 7 >TFTP_FILE=C2600-I-MZ.122-11.BIN (上传ios文件的名称)
rommon 8>sync (保存参数配置)
rommon 9 >set (查看)
rommon 10 > set
PS1=rommon ! >
BOOT=
IP_ADDRESS=10.32.10.1
IP_SUBNET_MASK=255.255.255.0
DEFAULT_GATEWAY=10.32.10.32
TFTP_SERVER=10.32.10.32
TFTP_FILE=C2600-I-MZ.122-11.BIN
BSI=0
RET_2_RTS=
?=0
rommon 11 >tftpdnld执行tftpdnld命令进行ios升级,有时可能会报错或命令不执行,这时只要用sync命令保存配置后,重新启动路由器(最好关掉电源再开机)后,再执行tftpdnld命令就可以了。
QUOTE:rommon 11 >tftpdnld(传送文件)出现提示选择y
IP_ADDRESS: 10.32.10.1
IP_SUBNET_MASK: 255.255.255.0
DEFAULT_GATEWAY: 10.32.10.32
TFTP_SERVER: 10.32.10.32
TFTP_FILE: C2600-I-MZ.122-11.BIN
Invoke this command for disaster recovery .ly.
WARNING: all existing data in all partitions . flash will be lost!
Do you wish to continue? y/n:
: y
Receiving C2600-I-MZ.122-11.BIN from 10.32.10.32!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
…
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
File reception completed.
Copying file C2600-I-MZ.122-11.BIN to flash.
Erasing flash at 0x607c0000
program flash location 0x605b0000
rommon 13 >
在rommon 13 >提示符下键入reset,或重新启动路由器(power-cycle),进入正常引导状态,
Fastest Way to Recover or Upgrade Cisco IOS using tftpdnld
如果IOS被损坏,例如升级IOS过程中断电等。
可以在ROM monitor commands模式下通过2种方法恢复:xmodem 或者 tftpdnld
1.xmodem
xmodem—Use this if the computer attached to your console has a terminal emulator that has xmodem capability.
第一步:
先打开超级终端,进入rommon 模式(Ctrl+Break组合键),键入confreg, 如下:
rommon 1 > confreg 回车
onfiguration Summary
enabled are:
load rom after netboot fails
console baud: 9600
boot: image specified by the boot system commands or default to: cisco2-C2600
****显示
do you wish to change the configuration? y/n
: y (选择 yes)
enable "diagnostic mode"? y/n
: n (选择 no)
enable "use net in IP bcast address"? y/n
: n (选择 no)
disable "load rom after netboot fails"y/n
: n (选择 no)
enable "use all zero broadcast"? y/n
: n (选择 no)
enable "break/abort has effect"? y/n
: n (选择 no)
enable "ignore system config info"? y/n
: n (选择 no)
change console baud rate y/n
: y (选择 yes)
enter rate: 0 = 9600, 1= 4800, 2 = 1200, 3 = 2400 4 = 19200, 5 = 38400, 6 = 57600, 7 = 115200 [0]: 7 (选择 7,用最大的115200速率的xmodem传输)
change the boot characteristics? y/n
: n (选择 no)
Configuration Summary
enabled are:
load rom after netboot fails
console baud: 115200
boot: image specified by
the boot system commands or default to: cisco2-C2600
do you wish to change the configuration? y/n
: n (选择 no)
You must reset or power cycle for new config to take effect
rommon 2 > reset 回车
注意:在此时键入 reset键,然后再修改超级终端里设置端,重新建立一个超级终端连接之前,开始定义串口速度(我的电脑速率为115200,记住,一定这么做,(期间系统重新启动)启动后,出--端口属性----串口速度调为115200 ,否则出现乱码!
rommon 1> xmodem -cr
Do not start the sending program yet.
invoke this applicationonly for disaster recovery.
Do you wish to continue? y/n
: y (选择 yes)
Ready to receive file
此时,在超级终端的菜单上的“传送”---xmodem”协议,点击“发送”即可发送文件”----选择IOS镜像文件所在地以及选择使用“然后等待10-20分钟左右就把3-6M的IOS灌进去了
!!!! 会自动引导IOS(c2600-i-mz.122-8.T10.bin),进入EN模式,show flash: ,会发现损坏的IOS版本被删除,其实只是做了一个1 5850064 c2600-i-mz.122-8.T10.bin(delected)的标志,在EN模式下,用
squeeze flash:c2600-i-mz.122-8.T10.bin物理删除它。(#######¥¥¥¥¥记住一定不要重起)
其实IOS没有倒入,是调用的配置文件。
show flash:
会发现IOS没有
(#######¥¥¥¥¥记住一定不要重起)
第二步:倒入IOS
手动把E0/1用直连线插到交换机上,笔记本的网卡也用直连线也插到交换机上
en
show run
conf t
int fa0/1
ip add 192.168.0.2 255.255.255.0
no shu
exit
exit
wr
笔记本网卡设置成192.168.0.1 255.255.255.0
在ROUTE上 ping 192.168.0.1
打开TFTP,把IOS拷贝到TFTP目录下(c2600-i-mz.122-8.T10.bin)
en
copy tftp flash:c2600-i-mz.122-8.T10.bin
完毕后
show flash
(!!!!!绝对不能重起)
看到版本c2600-i-mz.122-8.T10.bin,后面没有delected
倒入成功
conf t
config-register 0x2102
boot system flash c2600-i-mz.122-8.T10.bin
exit
exit
wr
reload
会引导到正常的操作模式下,成功
第三步:
改到9600,可要可不要
方法2:tftpdnld tftpdnld—Use this if you have a TFTP server directly connected to the Ethernet 0 port.
1、用Cisco原配的线缆连接路由器的console口与PC机的COM1,使用PC机的超级终端软件访问路由器;用一根双绞线连接路由器的eth0/0口与PC机的网卡。
2、将路由器的eth0/0口IP地址设为10.32.10.32;PC机的IP地址设为10.32.10.1.将要升级的IOS映象文件拷贝到相关的目录中,并运行TFTP服务器软件,通过菜单设置Root目录为拷贝IOS映象文件所在目录。
3、通过set 命令查看配置参数
QUOTE:rommon 2 > set
PS1=rommon ! >
BOOT=
BSI=0
RET_2_RTS=
?=0 4、在 rommon 状态下输入:(注意大小写)
QUOTE:rommon 3 >IP_ADDRESS=10.32.10.1 (路由器的ip地址)
rommon 4 >IP_SUBNET_MASK=255.255.255.0 (路由器的掩码)
rommon 5 >DEFAULT_GATEWAY=10.32.10.32 (缺省网关,是pc机的ip地址)
rommon 6 >TFTP_SERVER=10.32.10.32 (是pc机的ip地址)
rommon 7 >TFTP_FILE=C2600-I-MZ.122-11.BIN (上传ios文件的名称)
rommon 8>sync (保存参数配置)
rommon 9 >set (查看)
rommon 10 > set
PS1=rommon ! >
BOOT=
IP_ADDRESS=10.32.10.1
IP_SUBNET_MASK=255.255.255.0
DEFAULT_GATEWAY=10.32.10.32
TFTP_SERVER=10.32.10.32
TFTP_FILE=C2600-I-MZ.122-11.BIN
BSI=0
RET_2_RTS=
?=0
rommon 11 >tftpdnld执行tftpdnld命令进行ios升级,有时可能会报错或命令不执行,这时只要用sync命令保存配置后,重新启动路由器(最好关掉电源再开机)后,再执行tftpdnld命令就可以了。
QUOTE:rommon 11 >tftpdnld(传送文件)出现提示选择y
IP_ADDRESS: 10.32.10.1
IP_SUBNET_MASK: 255.255.255.0
DEFAULT_GATEWAY: 10.32.10.32
TFTP_SERVER: 10.32.10.32
TFTP_FILE: C2600-I-MZ.122-11.BIN
Invoke this command for disaster recovery .ly.
WARNING: all existing data in all partitions . flash will be lost!
Do you wish to continue? y/n:
: y
Receiving C2600-I-MZ.122-11.BIN from 10.32.10.32!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
…
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
File reception completed.
Copying file C2600-I-MZ.122-11.BIN to flash.
Erasing flash at 0x607c0000
program flash location 0x605b0000
rommon 13 >
在rommon 13 >提示符下键入reset,或重新启动路由器(power-cycle),进入正常引导状态,
相关文章推荐
- Cisco 2005系列路由器IOS映像备份与恢复
- cisco路由器IOS 恢复
- Cisco路由器IOS印象恢复及升级
- Cisco路由器在rommon状态下恢复IOS
- 路由器、交换机密码恢复、路由器IOS灾难恢复
- cisco路由器IOS恢复方法之ROMMON恢复
- 在cisco路由器上使用TFTP备份/恢复交换路由的IOS文件
- 利用TFTP备份和恢复Cisco路由器的IOS
- 利用TFTP备份和恢复Cisco路由器的IOS
- cisco 交换机IOS灾难恢复
- 利用TFTP备份和恢复Cisco路由器的IOS
- 利用TFTP备份和恢复Cisco路由器的IOS
- Cisco路由器IOS映像恢复及升级方法
- Cisco路由器IOS映像恢复及升级方法
- 使用TFTP升级/恢复cisco路由器IOS
- Cisco路由器IOS映像恢复及升级方法
- Cisco路由器在rommon状态下恢复IOS的最简单方法
- Cisco路由器在rommon模式下几种恢复IOS的方法
- Cisco路由器IOS映像恢复及升级方法
- cisco的ios灾难恢复