CCNA(Stand-ALONE)Lab 13-RIP
2008-04-17 13:03
661 查看
Objective: configure Routers 1, 2, and 4 with IP addresses and the Routing Information Protocol (RIP).
Lab Equipment: Router 1, Router 2, and Router 4 from the eRouters menu
Background Reading: Lab Primer Lesson 7: Routing Protocols
Goals:
• Set the host name and bring up the interfaces.
• configure RIP.
• Select the directly connected networks.
• Display the routing table.
• Display the RIP protocol information.
1. configure Routers 1, 2, and 4 to the specifications outlined in the table and diagram below.
Router1:
Router2:
Router4:
2. On each router, verify that you can ping the directly connected neighbors.
Router1#ping 10.1.1.2
Router1#ping 172.16.10.2
Router2#ping 10.1.1.1
Router4#ping 172.16.10.1
3. Add RIP to Router1.
Router1#
Router1#configure terminal
Router1(config)#router rip
Router1(config-router)#
4. Add the network(s) to which Router1 is directly connected.
Router1(config-router)#network 10.0.0.0
Router1(config-router)#network 172.16.0.0
5. Add RIP to Router2.
Router2#
Router2#config terminal
Router2(config)# router rip
Router2(config-router)#
6. Add the network(s) to which Router2 is directly connected.
Router2(config-router)#network 10.0.0.0
7. Add RIP to Router4.
Router4#
Router4#config terminal
Router4(config)#router rip
Router4(config-router)#
8. Add the network(s) to which Router4 is directly connected.
Router4(config-router)#network 172.16.0.0
9. Now, RIP should be running on all three routers. See if you can ping between routers that are not directly connected. For instance, from Router2 you should now be able to ping Router4’s serial 0 interface.
Router2#ping 172.16.10.2
10. Connect to Router4, and ping Router2’s Ethernet 0 interface.
Router4#ping 10.1.1.2
If you can ping both devices, then you have correctly configured routing. If the pings were not successful, trace back through the steps.
11. Now, issue the command to display the routing table on Router4.
Router4#show ip route
12. Finally, display specific IP routing protocol information on Router4.
Router4#show ip protocol
***************************************************
Above:CCNA(Stand-ALONE)Lab 12-Static Routes
Next:CCNA(Stand-ALONE)Lab 14-Troubleshooting RIP
Lab Equipment: Router 1, Router 2, and Router 4 from the eRouters menu
Background Reading: Lab Primer Lesson 7: Routing Protocols
Goals:
• Set the host name and bring up the interfaces.
• configure RIP.
• Select the directly connected networks.
• Display the routing table.
• Display the RIP protocol information.
1. configure Routers 1, 2, and 4 to the specifications outlined in the table and diagram below.
Router1:
Router2:
Router4:
2. On each router, verify that you can ping the directly connected neighbors.
Router1#ping 10.1.1.2
Router1#ping 172.16.10.2
Router2#ping 10.1.1.1
Router4#ping 172.16.10.1
3. Add RIP to Router1.
Router1#
Router1#configure terminal
Router1(config)#router rip
Router1(config-router)#
4. Add the network(s) to which Router1 is directly connected.
Router1(config-router)#network 10.0.0.0
Router1(config-router)#network 172.16.0.0
5. Add RIP to Router2.
Router2#
Router2#config terminal
Router2(config)# router rip
Router2(config-router)#
6. Add the network(s) to which Router2 is directly connected.
Router2(config-router)#network 10.0.0.0
7. Add RIP to Router4.
Router4#
Router4#config terminal
Router4(config)#router rip
Router4(config-router)#
8. Add the network(s) to which Router4 is directly connected.
Router4(config-router)#network 172.16.0.0
9. Now, RIP should be running on all three routers. See if you can ping between routers that are not directly connected. For instance, from Router2 you should now be able to ping Router4’s serial 0 interface.
Router2#ping 172.16.10.2
10. Connect to Router4, and ping Router2’s Ethernet 0 interface.
Router4#ping 10.1.1.2
If you can ping both devices, then you have correctly configured routing. If the pings were not successful, trace back through the steps.
11. Now, issue the command to display the routing table on Router4.
Router4#show ip route
12. Finally, display specific IP routing protocol information on Router4.
Router4#show ip protocol
***************************************************
Above:CCNA(Stand-ALONE)Lab 12-Static Routes
Next:CCNA(Stand-ALONE)Lab 14-Troubleshooting RIP
相关文章推荐
- CCNA(Stand-ALONE)Lab 14-Troubleshooting RIP
- CCNA(Stand-ALONE)Lab 23-Introduction to Basic Switch Commands
- CCNA(Stand-ALONE)Lab 29-Extended Access Lists
- CCNA(Stand-ALONE)Lab 7-Copy Command
- CCNA(Stand-ALONE)Lab 11-Creating a Host Table
- CCNA(Stand-ALONE)Lab 30-Verify Extended Access Lists
- CCNA(Stand-ALONE)Lab1-Connecting to a Router
- CCNA(Stand-ALONE)Lab 12-Static Routes
- CCNA(Stand-ALONE)Lab 15-IGRP
- CCNA(Stand-ALONE)Lab 19-Loading Router configurations
- CCNA(Stand-ALONE)Lab 8-Introduction to Interface configuration
- CCNA(Stand-ALONE)Lab 20-Copying and Pasting configurations
- CCNA(Stand-ALONE)Lab 24-Frame Relay
- CCNA(Stand-ALONE)Lab 31-Named Access Lists
- CCNA(Stand-ALONE)Lab 5-Extended Basics
- CCNA(Stand-ALONE)Lab 9-Introduction to IP
- CCNA(Stand-ALONE)Lab 16-PPP With CHAP Authentication
- CCNA(Stand-ALONE)Lab 21-ISDN
- CCNA(Stand-ALONE)Lab 25-Frame Relay Hub-and-Spoke Topology
- CCNA(Stand-ALONE)Lab 27-Standard Access Lists