Cisco 2900xl/3500xl/2950/3550密码恢复流程
2007-12-20 13:08
453 查看
简介:本文详细描述了对于2900xl/3500xl/2950/3550系列交换机的enable密码恢复流程
一、将一台终端或装有超级终端软件的PC接到交换机的console口上。终端参数设置如下:
速率:9600bps
检较位:无
数据位:8
停止位:1
流控:无
二、拨掉电源
三、按住前面板的mode键不放,插上电源,等3-5秒后松开mode键。你会看到如下提示:
The system has been interrupted prior to initializing the flash file system.
The following commands will initialize the flash file system, and finish loading
the operating system software:
flash_init
load_helper
boot
四、输入flash_init
五、输入load _helper
六、输入dir flash:
注意,不要少了flash后面的冒号,屏幕出现如下提示。
Directory of flash:
2 -rwx 843947 Mar 01 1993 00:02:18 C2900XL-c3h2s-mz-12.1-WC5.bin
4 drwx 3776 Mar 01 1993 01:23:24 html
66 -rwx 130 Jan 01 1970 00:01:19 env_vars
68 -rwx 1296 Mar 01 1993 06:55:51 config.text
1728000 bytes total (456704 bytes free)
七、输入rename flash:config.text flash:config.old
八、输入boot引导系统。
九、当出现如下提示时,输入N:
Continue with the configuration dialog? [yes/no] : N
十、用en进入enable状态,并将文件config.old改回config.text,命令如下:
rename flash:config.old flash:config.text
十一、将原配置装入内存,命令如下:
2900# copy flash:config.text system:running-config
十二、修改密码:
2900xl#conf t
2900xl(config)#no enable secret
2900xl(config)#enable secret ultra
2900xl(config)#exit
十三、telnet到交换机上,验证密码是否修改成功
十四、将配置写入nvram
2900xl#wr mem
以上步骤中,第十一、十二步需要特别注意,前者是为了保留配置,后者需要注意的是如果不使用no enable secret的话,新密码将不起作用。本文出自 51CTO.COM技术博客
一、将一台终端或装有超级终端软件的PC接到交换机的console口上。终端参数设置如下:
速率:9600bps
检较位:无
数据位:8
停止位:1
流控:无
二、拨掉电源
三、按住前面板的mode键不放,插上电源,等3-5秒后松开mode键。你会看到如下提示:
The system has been interrupted prior to initializing the flash file system.
The following commands will initialize the flash file system, and finish loading
the operating system software:
flash_init
load_helper
boot
四、输入flash_init
五、输入load _helper
六、输入dir flash:
注意,不要少了flash后面的冒号,屏幕出现如下提示。
Directory of flash:
2 -rwx 843947 Mar 01 1993 00:02:18 C2900XL-c3h2s-mz-12.1-WC5.bin
4 drwx 3776 Mar 01 1993 01:23:24 html
66 -rwx 130 Jan 01 1970 00:01:19 env_vars
68 -rwx 1296 Mar 01 1993 06:55:51 config.text
1728000 bytes total (456704 bytes free)
七、输入rename flash:config.text flash:config.old
八、输入boot引导系统。
九、当出现如下提示时,输入N:
Continue with the configuration dialog? [yes/no] : N
十、用en进入enable状态,并将文件config.old改回config.text,命令如下:
rename flash:config.old flash:config.text
十一、将原配置装入内存,命令如下:
2900# copy flash:config.text system:running-config
十二、修改密码:
2900xl#conf t
2900xl(config)#no enable secret
2900xl(config)#enable secret ultra
2900xl(config)#exit
十三、telnet到交换机上,验证密码是否修改成功
十四、将配置写入nvram
2900xl#wr mem
以上步骤中,第十一、十二步需要特别注意,前者是为了保留配置,后者需要注意的是如果不使用no enable secret的话,新密码将不起作用。本文出自 51CTO.COM技术博客
相关文章推荐
- Cisco 2900xl/3500xl/2950/3550密码恢复流程
- Cisco 2900xl/3500xl/2950/3550密码恢复流程
- Cisco 2900xl/3500xl/2950/3550密码恢复流程
- cisco 2900xl, 3500xl, 2950, 3550密码恢复
- 网络工程师交换试验手册之二十三:Cisco 2900xl/3500xl/2950/3550密码恢复
- CISCO 3550 密码恢复
- CISCO-2950交换机密码恢复(不破坏原配置)
- cisco 2950 3550 3750 系列交换机密码破解
- Cisco 2950密码恢复
- cisco 2950密码恢复
- cisco 3550的enable密码忘记恢复方法
- Cisco 2950 密码恢复
- Cisco 2950 交换机恢复密码
- 转:cisco 2950交换机密码恢复
- CISCO-2950交换机密码恢复(不破坏原配置)
- cisco 交换机密码恢复
- Cisco路由器密码恢复
- 交换机密码(2950)的恢复
- cisco修改寄存器值及恢复密码
- 2种方法帮你恢复Cisco路由器的密码