Cisco CATALYST交换机端口监听配置
Cisco CATALYST交换机分为两 种,在CATALYST家族中称侦听端口为分析端 口(analysis port)。
1、Catalyst 2900XL/3500XL/2950系列交换机端口监听配 置 (基于CLI) 以下命令配置端口监听: port monitor 例 如,F0/1和F0/2、F0/3同属VLAN1,F0/1监听F0/2、F0/3端口: interface FastEthernet0/1 port monitor FastEthernet0/2 port monitor FastEthernet0/3 port monitor VLAN1
2、Catalyst 4000,5000 and 6000系列交换机端口监听配 置 (基于IOS) 以下命令配置端口监听: set span 例如,模块1中端口1和端口2同属VLAN1,端口3在VLAN2,端口4和5在VLAN2,端口2监听端 口1和3、4、5, set span 1/1,1/3-5 1/2
2950/3550/3750 格式如下: #monitor session number source interface mod_number/port_number both #monitor session number destination interface mod_mnumber/port_number
//rx-->指明是进端口得流量,tx-->出端口得流量 both 进出得流量
for example:
第一条镜像,将第一模块中的源端口为1-10的镜像到端口12上面; #monitor session 1 source interface 1/1-10 both #monitor session 1 destination interface 1/12 第二条镜像,将第二模块中的源端口为13-20的镜像到端口24上面; #monitor session 2 source interface 2/13-20 both #monitor session 2 destination interface 2/24
当有多条镜像、多个模块时改变其中的参数即可。
Catalyst 2950 3550不支持port monitor
C2950#configure terminal C2950(config)# C2950(config)#monitor session 1 source interface fastEthernet 0/2
!--- Interface fa 0/2 is configured as source port.
C2950(config)#monitor session 1 destination interface fastEthernet 0/3
!--- Interface fa0/3 is configured as destination port.
3COM交换机端口监听配置
在3COM交换机中,端口监听被称为“Roving Analysis”。 网络流量被监听的端口称作“监听口”(Monitor Port),连接监听设备的端口称作“分析 口”(Analyzer Port)。 以下命令配置端口监听: ● 指定分析 口 feature rovingAnalysis add,或缩 写 f r a, 例 如: Select menu option: feature rovingAn alysis add Select analysis slot: 1?& nbsp; Select analysis port: 2
● 指定监听口并启动端口监听 feature rovingAnalysis start,或缩 写 f r sta, 例 如: Select menu option: feature rovingAn alysis start Select slot to monitor ?(1-12): 1 Select port to monitor&nb sp;?(1-8): 3
● 停止端口监 听 feature rovingAnalysis stop,或缩 写 f r sto,
Intel交换机端口监听配置
Intel 称端口监听为“Mirror Ports”。 网络流量被监听的端口称作“源端 口”(Source Port),连接监听设备的端口称作“镜像 口”(Mirror Port)。 配置端口监听步骤如下: ● 在 navigation菜单,点击Statistics下的Mirror Ports,弹出Mirror Ports信 息。 ● 在Configure Source 列中点击端口来选择源端口, 弹出Mirror Ports Configuration。 ● 进行源端口设 置: 源端口是镜像流量的来源口,镜像口是接收来自源端口流量的端 口。 ● 点击Apply确定 可以选择三种监听的方 式: 1.连续(Always):镜像全部流量。 2.周期(Periodic):在一定周期内 镜像全部流量。镜像周期在Sampling Interval configuration中设置。 3 .禁止(Disabled):关闭流量镜像。
Avaya交换机端口监听配置
在Avaya交换机用户手册中,端口监 听被称为“端口镜像”(Port Mirror)。 以下命令配置端口监听: { set|clear } Port Mirror 设置端口侦 听:set port mirror <mod-port-range> source-port ?<mod-port-range> mirror-port <mod-port-spec> sampling { always | disable | periodic } [ max-packets-sec <max-packets-sec-value>?& nbsp;] [ piggyback-port<mod-port-spec> ]?&nb sp; 禁止端口监 听:clear port mirror <mod-port-range>
命令中,mod-port-range指定端口的范围;mod-port-spec指定特定的端口;piggyback-port指定双向镜像的端口; sampling指定镜像周期;max-packets-sec仅在sampling设置为periodic时使用,指定监听口每秒最多的数据报数量。
华为交换机端口监听配置 华为交换机用户手册中,端口监听被称为“端口镜 像”(Port Mirroring)。 使用Huawei Lanswitch View管 理系统添加一个镜像端口: ● 选 择Device Setup或Stack Setup。 ● 点 击Port Mirroring。 ● 点击Add按 钮。 ● 对于堆叠,点击Switch并从列表选择一个交换 机。 ● 点击Reflect from并选择流量将被镜像的端 口。 ● 点击Reflect to并选上面所选择的端口上的
|
|
原文地址 http://www.net130.com/CMS/Pub/Tech/tech_zh/2006_12_11_29910_2.htm |
内容来自用户分享和网络整理,不保证内容的准确性,如有侵权内容,可联系管理员处理